Question about Whirlpool Ultimate Care II LSQ9564J Top Load Washer

1 Answer

CAV 3951650 - HOW TO remove it?


Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers
Re: CAV 3951650 - HOW TO remove it? - Whirlpool Ultimate Care II LSQ9564J Top Load Washer Washing Machines

Toss it into yard lol

Posted on Dec 30, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

How do I remove the drum on my aav7000aww

To remove the inner tub
remove front panel
remove screws holding top to cabinet
raise top
remove hoses from tub cover
remove tub cover
remove agitator
remove bolts holding inner tub to hub. 5-6 hex head bolts
lift off inner tub

Aug 20, 2011 | Maytag Washing Machines

1 Answer

I have lost a "washable" bear in my HE2 front load washer. I paid sears nearly $200 last month when a small "beanie" hat got stuck somehow behind the gasket. I did nto see how the sears repairman removed...

Door Gasket Removal Procedure

  1. Unplug the washer for your safety.
  2. Open the door and locate the door gasket retaining hoop. Stretch the retaining hoop spring and remove the hoop from the perimeter of the door gasket.
  3. Peel back the door gasket from the lip of the tub into the drum.
  4. Remove the door switch from the front panel.
  5. Remove the top panel/cover of the machine.
  6. Remove the console.
  7. Remove the front panel.
  8. Carefully pull the door gasket from around the inlet and window washer tubes.
  9. Remove the door gasket retaining clamp by loosening the clamp screw on the upper right of the tub opening.
  10. Peel off the door gasket completely from the tub. Be careful not to tear or punch a hole on it.
  11. Reassemble the parts in reverse order of the removal procedures given.
Door Switch Removal
  1. Remove the screws holding the door switch on the right side of the door opening.
  2. Lift the door switch and pull it away from the front panel.
Top Cover Removal
  1. Remove the screws securing the top panel at the back of the machine and lift it off.
Console Removal
  1. Disconnect the ribbon connector from the left side of the central control unit which is located directly above the rear of the tub.
  2. Release the ribbon connector from the wiring harness brackets on the right side of the washer top.
  3. Pull the detergent dispenser drawer out and press down on the release tab at the back of the drawer then pull it completely out of the washer.
  4. Remove the screw in the recessed hole next to the drawer opening.
  5. Open the door and insert a flat-bladed screwdriver into the slot in the bottom center of the console.
  6. Push the console up to release the center tab and remove it from the washer.
Front Panel Removal
  1. Remove the three screws holding the toe panel to the front of the washer.
  2. Lift the toe panel slightly then pull it to the front to remove it.
  3. Remove the two bottom screws and two top screws holding the front panel to the washer.
  4. Remove the front panel from the washer.

Jan 21, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

How do I replace the CAM-AGIT on a Whirlpool Washer Model #395165

you have to remove the cover inside the upper agitator first, then you will see a plastic cover inside the top. it has 2 raised handle type tabs to pull on, then remove the cover and under it you will find a 7/16 bolt to remove and that will allow you to pull the tophalf of the agitator and change the agitate" dogs "

Dec 31, 2009 | Washing Machines

1 Answer


really tedious job. if you are really keen, pl. follow.
remove motor, remove shoker top pins, remove top stone, remove all hose connecting drum, remove heater/other connections, remove door gasket from front, support drum from top, remove springs, lower drum, dismantle drum in two pieces, remove inner steel drum.
well rest i think you can think yourself.

Oct 30, 2009 | LG WM-0532HW Front Load Washer

2 Answers

How to I remove the drum from a Hotpoint WM64 washing machine? I need to change the bearings.

Remove top cover and rear panel.
Remove belt and drum drive pulley.Remove clamp that secures door seal
Remove top control console panel.
Remove door lock.
Remove screws top and bottom holding front panel, remove front panel.
Remove spring clips holding plastic drum front, lift to one side plastic drum front cover.
Tap drum shaft to remove drum from container, remove bearings.
Please rate my solution.

Sep 04, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

How do remove front seal on my ultima wf865

Remove top cover, unclip the control board, and unplug the lead to the board, remove screws holding board and remove same.
Remove front panel screws, remove screws holding door lock,remove clamp securing front seal ,remove seal, slide panel up and remove.
Change seal.
Re-assemble in reverse order.
Please rate my solution.

Jul 29, 2009 | Hotpoint Ultima WF865 Front Load Washer

1 Answer

Door seal leaks cant how to remove and reinstall

1: remove the top panel
2: remove the lower front panel
3; remove the control panel
4: remove the screws holding the door switch
5: remove clamparound the door seal and remove front panel (2 screws bottom and 2 up)
6: remove clip around door seal that holds tothe tub
7: replace seal....

there you go!!!

Jul 04, 2009 | Whirlpool Washing Machines

1 Answer

Cleaning the drum of the Whirlpool 3 LSR 6233 EQO (get it out)

Remove two screws that hold the control panel,pull forward and lift ,tilt back. Unplug door switch and remove the gold clips that hold the back to the top of washer cabinet. Lean cabinet towards front and remove. Unsnap tub ring at top from outer tub. Remove fabric softener dispenser cup at top of agitator. Remove snapped in plastic cover and seal underneath. Remove bolt under the cover. Remove agitator. Remove spanner nut that holds drum in and remove drum.

May 13, 2009 | Whirlpool LSR6332K Top Load Washer

1 Answer

How to replace the gear case for whirlpool washer lsn1000kq0

remove 2 screws on rear of console lift console forward and roll back remove the lid switch connector remove the 2 clips on each side pull rear of cabinet forwardand slide cabinet off remove screws in center of agitator under cap and pull off ..lean washer backward remove pump clips and hoses remove 2 screws in motor clamps remove clamps and motor remove 3 1/2 in bolts holding gearcase to bottom slide gearcase out remove clutch and reinstall on new gearcase if you go slow and take note reassembly not that hard

Nov 26, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

2 Answers

Door seal replacement

This video will show you how to change a door seal on this Bosch classics 1200 WFL 2463GB/12 FD

Jul 24, 2008 | Washing Machines

Not finding what you are looking for?
Whirlpool Ultimate Care II LSQ9564J Top Load Washer Logo

Related Topics:

899 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides