Question about Directv D10 DTV Receiver

2 Answers

New roof This is not actually a receiver problem, but rather the fact that I recently had a new roof put on. The roofer replaced the dish, but it is out of alignment. I'm looking for information on how to realign the dish myself. thx

Posted by on

  • gonepats Jan 01, 2008

    I have the look, angle, and azimuth for the dish, as well as the signal strength menu. I was looking for step by step instructions on how to go from there - or a website with that info. I should have given more info. Thx

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 26 Answers

What you want to do is looen the bolts on the neck collar there should be 3 of them and i believe they are half inch or 7/16. once u loosen them turn our tv p so u can hear the signal strength and carefully swing the dish from left to right. when u get a good signal tightn it down and then loosen up the bolts on the side of the angle bracket should be 2 bolts same size as the neck bolts loosen them slowwly and move you dish up and down ti you find your best signal.

good luck

please rate

Posted on Jan 13, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

On my receiver there is a setting for signal strength on the menu/setup. You can have some one watch the signal meter and try but with out a meter at the dish you might be looking for a while. There are websites that give the look angle and azimuth from your location if you have a compass.

Posted on Dec 29, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flash a metal roof to a wall


if its brick you can cut into it so you can tuck the flashing in and apply sealent and run the flashing on top of metal roofing apply sealent inbetween before screwing down.

Sep 29, 2014 | Roofing

1 Answer

How do I re-roof my house easily


If you mean re shingling, here in USA there are usually building codes to be complied with, such as: If there is just one layer of shingles on the building, you can add a second layer, but if there are two layers of shingles they both must be removed, and new tar paper installed before a layer of shingles are placed. Also with all shingles removed is a time to inspect and replace all rotten wood of roof, before repapering and reshingling. If you've never seen of watched the process by done by professionals, I'd recommend getting bids from three roofers, and pay the best price to do it. Get a full written contract before they start, because there could be significant damages if there are leaks after the job is done.
Maybe watch some youtube videos of roof reshingling. there are many special tool techniques to do the job right, (And not fall off the roof either)

Sep 26, 2014 | Heating & Cooling

1 Answer

Leaking roof


You need to call a roofer to install some metal flashing pieces. That will create a metal channel for the water to flow down instead of through your roof. Look in the Yellow Pages of your local phone book.

Dec 30, 2013 | Computers & Internet

1 Answer

I had a new roof up on my house about 6 years ago. I just went into my attic and found wood that was rotten and was not replaced by the roofer. How can I replace the wood?


that would depend on if what you wish replaced are rafters, trusses or sheeting. rafters and trusses can have new pieces cut to fit and 'married' in bridging any weak areas. unfortunately, sheeting replacement means stripping shingle and paper to expose the damaged areas, cutting them out, new sheeting installed, repaper and reshingle. Hope you got a warranty from the contractor.

Oct 25, 2013 | Dometic Rooftop RV Air Conditioner

1 Answer

GH7208XRS Whirlpool sounds like screw in housing how to get it out


Drop a magnet tied to a piece of string down the same spot where you believe the roofers may have dropped the screw. This should pick it up for you.

Feb 06, 2012 | Air Tools & Compressors

1 Answer

My Panasonic FV-11VQL2 seems to have the damper stuck in the closed position. The fan does not exhaust well, ever since we got a new roof (vent and 4" duct too). Any way to unstuck it without going into...


Hubby went into attic. The roofer did a poor job installing the new 4" duct and roof vent; duct was poorly attached and pinched at both ends. He redid both connections, and now the fan works well----no more foggy, drippy mirrors!
So, the fan is fine------the installation of the new roof vent and duct was shoddy.

Aug 24, 2009 | Panasonic Dryers

5 Answers

Wet ceilings


You must conact your roofer and complain... COMPLAIN.. it sounds like you have a leak and the installers have allowed moistere to get under the roofing materials...!!!

Basically water expands when it freezes (ice cube tray.. over filled ) so if there's any kind of leak the water penetrates.. feezes allowing it to migrate up under the materials and then as the warm air from inside the attic causes the ice to then melt. I'd call and find out what the deal is.. especially if this has been going on SINCE the new roof was installed....

good luck

Oct 26, 2008 | Measuring Tools & Sensors

Not finding what you are looking for?
Directv D10 DTV Receiver Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Directv Televison & Video Experts

john milligan

Level 3 Expert

514 Answers

The Knight
The Knight

Level 3 Expert

75846 Answers

rundiggity

Level 2 Expert

52 Answers

Are you a Directv Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...