Question about GE WCVH6260F Front Load Washer

1 Answer

Error codes??? Where can I get the error codes to display on my GE WCVH6260FWW washer?  If the contorl module detects an error, will it display the error on the front?

Posted by on

  • 3 more comments 
  • David Steinhorn
    David Steinhorn Dec 29, 2007

    My problem is: Our 6-month old washer goes through the initial wash cycle but does not
    spin the excess water out at the end of cycles. Many minutes before
    the end, the Pause/Start button light starts flashing -> when
    pushed, the washer starts water flowing into the drum for many minutes
    but does not ever get to the spin cycle.

  • David Steinhorn
    David Steinhorn Dec 29, 2007

    I opened the filter and got some coins out but nothing else was in there. I have gone through the manual several times.

    Can you explain how a piece of string would keep it from spinning if the water is pumped out completely?

  • David Steinhorn
    David Steinhorn Dec 29, 2007

    It spin just fine in the wash cycle, but doesn't go to spin nor agitate during the rinse cycle.

  • David Steinhorn
    David Steinhorn Dec 30, 2007

    It basically stopped from one day to the next. It did not seem to lose energy from one day to the next.

  • David Steinhorn
    David Steinhorn Dec 31, 2007

    I paid my $10 for the "Premium/Expert Service" and have received nothing more than generic advice on this site. I would strongly advise others to not waste their money here. In addition, my specific question about how to find "Error codes" did not get answered, and it appears that the respondent did not even seem to address my specific washer model. Shame on you for this lame service.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 347 Answers

Hi DMS1, your wacher might have gotten stuck with somthing. Maybe a piece of string or just dirt.
Have you already tried to open it and clean it?

Posted on Dec 29, 2007

  • 1 more comment 
  • Santiago Vallejo
    Santiago Vallejo Dec 29, 2007

    Did you already read yoru manual?
    Go here if you dont have one. http://products.geappliances.com/ApplPro...
    It might also be the belt of the washing machine, try tu unplug it and check its back (maybe its inside) and see if the belt is not broken.

  • Santiago Vallejo
    Santiago Vallejo Dec 29, 2007

    i was wondering if maybe something got stucked, and it prevented it from spinning.
    It seem that is not the problem.
    Can you locate the belt and see if it is working properly. (maybe its stuck, or broken)

  • Santiago Vallejo
    Santiago Vallejo Dec 30, 2007

    DMS When did you start having this problem, did it spin & agitate in rinse mode, and did it stop form one day to another or did it start losing energy untill one day it didnt moved anymore in rinse mode?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Intuitive type. error code 241 appears what does this mean and can i fix it myself


Hi i googled error code on fisher and paykel and found this link-->
http://www.searspartsdirect.com/washer-repair/error-codes/fisher-paykel-aquasmart-top-load-washer-error-codes.html
If you scroll down the page in the link the error code 241 says
"Motor control module failure", Unplug the washer and replace the motor control module. OR
"Display module failure", Unplug the washer and replace the display module...... Good luck...

Mar 11, 2016 | Fisher and Paykel Washing Machines

1 Answer

Fh error code wirpool duet washer


Display shows F20 or FH - Front-load washer ' Whirlpool ...

https://www.whirlpool.com/...fh-front-load-...

Whirlpool Home AppliancesQuestion: Display shows F20 or FH - Front-load washer. Answer. Image. or. Image. or. Image. This error code indicates a water supply problem. Are both the hot ...

whirlpool duet error code FH - Appliance Repair Forum

forum.appliancepartspros.com > Appliance Repair Help > Washer Repair

Jan 5, 2009 - 10 posts - ‎1 author
... Repair Help > Washer Repair » whirlpool duet error code FH .... FH No water detected entering machine or Pressure switch trip not detected. Whirlpool Duet diagnostic code C:03 error code FH
1 post
Dec 5, 2014
Whirlpool Duet Washer HF Error Code
3 posts
Jun 10, 2013
FH Error Code on Whirlpool Duet Washer
2 posts
Mar 11, 2013
FH error code
9 posts
Sep 13, 2008
More results from forum.appliancepartspros.com

Stumped on error code FH for Whirlpool Duet front load washer .


Jan 08, 2016 | Washing Machines

1 Answer

How do I pull up error codes


Follow these steps to enter the service mode on a GE front load washer. 1. Close the door.

2. Clear current cycles by pressing the power button. Make sure the screen is blank before attempting to enter the service mode.

3. Disconnect power to washer for at least 30 seconds.

4. Reconnect the power and within 30 seconds of reconnecting power complete the next step.

5. Press signal -delay start -signal - delay start.
If you successfully enter the washer into the service mode, t01 will be displayed and the door will lock.
Here's a link to the codes: http://www.appliance-repair-it.com/GE_front_load_washer.html

Good luck with your troubleshooting!

May 28, 2014 | GE WCVH6260FWW

1 Answer

F&P GW709 top loader filling water intervally


Error Code 105
105. (01101001) Phase 2 to 5 - Comms. Error Time-out
These faults are reported when the Display module detects an error in the communications
between the Display module and the Motor Controller.
NB. If the product is an IW, check that the motor controller is not 426520. If it is replace with a
compatible part. This is incompatible and will give a fault code 105 at the start of agitate. Not
before! If it is a 426520 replace motor controller with a compatible part.
Primary Source - Display module
Action - Replace Display module.
Secondary Source - Motor Controller
Action - Replace Motor Controller
Tertiary Source - Rotor Position Sensor (Phase 5 Only)
Action - Replace Rotor Position Sensor. If the new Rotor Position Sensor corrects the fault refit
the original display module and motor controller.

Aug 02, 2013 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Displays code 107


Error code 107.
(01101011) Motor Control Module Reset Error
The Display Module has detected that the Motor Control Module has reset when it should not have. This can be due to a Motor Control Module supply disturbance or microprocessor failure.
Primary Source: Motor Control Module.
Action: Replace Motor Control Module.

Mar 15, 2013 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

No hot water cycle on ge wcvh6260fww


You need to replace the water inlet valve. Here is the part to order.
I have the complete service manual available if you should need it, post your email address.

Feb 17, 2013 | GE WCVH6260FWW

1 Answer

Fisher Paykel Smartdrive MW058K error code 106


106. (01101010) Display Module to Motor Control Module Communications Error
These faults are reported when the Display Module detects an error in the communications
between the Display Module and the Motor Control Module.
Primary Source: Display Module.
Action: Replace Display Module.
Secondary Source: Motor Control Module.
Action: Replace Motor Control Module.

Jul 23, 2012 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

What is code 89?


81. - 95. (0101xxxx) Phase 2 to 3 - Display/ Motor Controller.
See fault code 106
104. (01101000) Phase 2 to 6 See fault code 106
106. (01101010) Phase 2 to 3 - Display to Motor Controller module
Communications Errors (Phase 6 IW also)
These faults are reported when the Display module detects an error in the
communications between the Display module and the Motor Controller module.
Primary Source: Display module.
Action:
Replace Display module.
Secondary Source: Motor Controller module.
Action:
Replace Motor Controller module. If the new Motor Controller module corrects the fault, refit the original Display module.

Feb 18, 2012 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fix code 104


104. (01101000) See Fault Code 106
106. (01101010) Display Module to Motor Control Module Communications Error
These faults are reported when the Display Module detects an error in the communications
between the Display Module and the Motor Control Module.
Primary Source: Display Module.
Action: Replace Display Module.
Secondary Source: Motor Control Module.
Action: Replace Motor Control Module.

Jan 24, 2012 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Error codes????


Remove the top cover. Inside there's a service manual that decribes the error codes and how to read them.

Dec 29, 2007 | GE WCVH6260F Front Load Washer

Not finding what you are looking for?
GE WCVH6260F Front Load Washer Logo

Related Topics:

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Marvin
Marvin

Level 3 Expert

82322 Answers

geapptech

Level 2 Expert

153 Answers

Are you a GE Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...