Question about Neoware CAPIO 508 TC (cp4a-aa-aa0) Network Terminal

1 Answer

Help!!!!!!!!!!!!!!! Monitor say out of frequency range and i dont know how to go into safe mode to change the settings. any help woul be greatly appreciated Thanks j

Posted by on


1 Answer

To go in to safe mode you need to press F8 function key when you start your system. You need to press that key continously till you get the list of modes (normal, command prompt, safe mode, etc.)
over there you select enable VGA mode option and then your system will automatically set to the default settings.

Posted on Dec 31, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My pc is hcl monitor working on windows 7 When I start my Pc the windows comes directly shows that Attention Not Support Out Of Range I.know pressing F8 Key but Nothing is happening help

Sounds like you set the refresh frequency/resolution of your monitor to a value not supported by the monitor. You need to restart in safe mode and reset the resolution.

Keep pressing F8 at boot until the menu appears. Try restoring to a previous point.

Or try
- Boot in Safe Mode with networking and Uninstall your current GPU Drivers.
- Download the current Drivers and install
- Restart the PC in the Low resolution Mode (F8 Safe Mode launch menu)
- Use your Graphics Card Control Panel and Force change your settings back to the original working ones.

Mar 21, 2016 | Computers & Internet

1 Answer

I get a message out of range.

your resolution is set too high.. change to VGA and move out from there. if the computer is set too high and you can not see boot into safe mode which should be VGA and set accordingly.

Nov 06, 2013 | Envision G22LWK 22" LCD Monitor

2 Answers

Can't get anything on my monitor but 'out of frequency range' But I can't get anything on the monitor to be able to get into the computer to reset the frequency. Help

Restart the computer. As soon as the bios start screen displays, start hitting F8, about once a second. You will eventually get the windows start menu. Use "Last known good..." or VGA mode. Last known good should do it. If not, VGA mode will allow you to get into windows and change your resolution settings, then reboot and get back to work.

Jul 06, 2011 | Gateway GT5220 PC Desktop

1 Answer

Screen says "OUT OF RANGE H:27.8K V: 62.0

That's the monitor telling you it's getting a signal it can't handle. The H and V values are the horizontal and vertical frequencies that control the display. They change depending on your computer's video card settings. The monitor can be damaged if run at frequencies outside its safe range, and it displays the message you're seeing to protect itself.

Start your computer. When the manufacturer's splash screen (logo screen) comes on, press the F8 several times. This will get you to a startup options menu. Select "Start in VGA mode" from the list. Windows will start up then with settings every monitor can handle, and you'll be able to see again.

You might have a game or other graphics application that changes video settings to something the monitor can't handle. If this is the case, and those settings are required, you'll need to invest in a monitor with a greater settings range.

Feb 04, 2010 | Hyundai ImageQuest QV770 17 in.CRT...

3 Answers

I get a message, "Frequency out of range. Nothibng else. The menue and other buttons don't do anything. Nothing else shows. I swapped out the monitor and the new one works.

This problem arise when your computer AGP driver not adjust monitor fix it restart your computer and run safe mode settings resolution area(must be choice less area)or select 1024X768 pixel monitor frequency 60Hz press apply set OK.restart your computer.Run again normal mode.May be fix your problem.

Dec 27, 2009 | Princeton Digital VL1916 19" LCD Monitor

1 Answer

Hi need some help with 17" philips crt comes on runs until windows start then switch of all power wont come back on for 15min restart pc then screen display out of frequency range, set frequency range down...

You can try starting your computer in safe mode and restore your computer to another safe point. usually this problem is caused by an update or a new driver installation/update...

Mar 08, 2009 | LG Studioworks 775N 17" CRT Monitor

1 Answer

Out of frequency range set low resolution or refer monitor manual


Feb 06, 2009 | Compaq CV 7500 17" CRT Monitor

3 Answers

Out of range

Setting the Refresh Rate in Enable VGA Mode - Windows XP

You will need to go into Enable VGA Mode to change the refresh rate.
  1. Restart the computer and repeatedly tap the F8 key on your keyboard until the Windows Advanced Options Menu appears.

  2. Select “Enable VGA Mode” and press Enter.

  3. If asked to choose your operating system just press Enter.

  4. Once the computer has finished booting up go to Start -> Settings -> Control Panel -> Display -> Settings -> Advanced -> Monitor.

  5. Change your Refresh Rate/Refresh Frequency to a lower setting.

  6. Click Apply to confirm the change.

  7. Close all open windows and restart your computer.
* Click here for help determining the optimal refresh rate for your monitor

Sep 24, 2008 | Computers & Internet

1 Answer

I was adjusting picture on monitor and now picture completely messed up

  • Signal out of Range.
  • Out Of Scan Range
  • Horizontal frequency is out of range.
  • Cannot Display This Video Mode Out of Sync

This issue may occur if the signal from the video adapter exceeds the scan range of the monitor. The video adapter setting for updating the screen (the refresh rate) is incompatible with the monitor.
you should reinstall your video drivers in safe mode.

To restart in safe mode repeatedly press the F8 key during the computer startup. This will bring a menu where you'll be able to choose safe mode.

LCD monitor 60 - 75 Hz

Jan 25, 2008 | IBM E74 17" CRT Monitor

Not finding what you are looking for?
Neoware CAPIO 508 TC (cp4a-aa-aa0) Network Terminal Logo

Related Topics:

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Neoware Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers


Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Neoware Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides