Question about Mercury P4VM800M7 Motherboard

5 Answers

Mer cury PVM7 mobo wont display on monitor

Dont know about the entire mobo model number but it has PVM7 etched on the mobo. and the manual shows PVM7
and manual mentions VIA P4M800 . so I am assuming it is this one.
it has been working fine but it will not display video anymore. the monitor(s) I tried just blink the yellow light on the front of monitor and never goes to green. nothing displays. monitor is plugged into the mobo video plug.
I tried using an AGP card and still nothing displays.
I ripped the PC apart to get everything disconnecetd and nothing displays butthe CPU fan spins and when the HD
and FD and CD ROM were connected, the HD started running and the CD rom kept blinking like it was needing something in it.

if it is the mobo anyone know if it can be repaired?
and who could do it in san diego area?

Posted by on

  • swbtmis Dec 29, 2007

    thanks. I wasn't clear. it was working just fine using the 32MB video plug that is part of the mobo. then it just died, and I cant display anything. not even the BIOS/setup. nothing displays at all, ever.

    I even tried clearing the CMOS with the JUMPER switch. still nothing.

    I am going to try some of my other video cards, PCI, AGP etc.

    even when I disconnect the keyboard and moyse and pull out all the RAM, I dont get any POST beeps .

  • Anonymous Nov 26, 2008

    Same issues with my mother board also.. tried to fetch solutions from google all over i found head of same issues not found any answers :-(

×

Ad

5 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I want the display driver

Posted on Apr 07, 2008

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 205 Answers

So I think you are saying it did work and then stopped, right?

If that's the case then I would try booting into the BIOS setup and reseting it first. If that does not work then I would reboot into the BIOS again and see if there is something there you need to enable for the AGP port to function.

If all this fails then you most likely have a bad motherboard. It's probably not worth the money to consider having it repaired, and I doubt you'd find anyone who's even interested trying.

Good luck.

Posted on Dec 28, 2007

  • ohiotom Dec 29, 2007

    If you disconnected everything (including HDD and CD/DVD) and you still get no POST beeps then you either have a bad motherboard or a bad power supply. Do you have another power supply you can try?

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 28 Answers

Fiend your solution direct from mercury. Here is your solution.....
Mer cury PVM7  mobo wont display on monitor - 71707e3.jpg
http://www.mercury.com/motherboard/prob676ijt65/solution

aapor-12

Posted on Aug 29, 2009

******** I WANT TO DOWNLOAD THE SOFTWARE YA

Posted on Apr 05, 2008

Give me drivers

Posted on Feb 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

965gdag lf


Go to your manual that came with the motherboard (mobo) and look up the FF post and what it means. If you don't have a manual go to the manufacturer's website and hope that they posted one in the Downloads or Support section for your computer.
OR go to your computer manufacturer's website and do the same thing, only look up the model number of your computer.
If still no help, go HERE, log in and post your question in the Hardware section of the forum. Lots of knowledgeable folks there to help.

Oct 13, 2013 | Computers & Internet

1 Answer

I turn on my computer and i don't see anything


Guess what? I don't see it either.

Oh,....that's because you're there, and I'm here, and.............never mind.

(OH, I'm jus jokin'!)

Would be helpful to know the laptop manufacturer name, and model number, though. The name you know, the model number is on the bottom of the laptop.

Diagnose to see what the problem is;

A) Graphics chipset,
Or
B) Video Cable,
Or
C) In the Display Assembly

1) Suggest start with attaching a VGA monitor to the laptop.

Laptop OFF, monitor OFF, attach the VGA cable of a VGA monitor, to the VGA connector on the laptop.

Example of a VGA Cable, and VGA connector,

http://en.wikipedia.org/wiki/VGA_connector

You can use a CRT type of monitor, (Looks like a small TV), or a flat LCD screen monitor if it has a VGA cable.

2) Turn the monitor on. If a CRT type allow it to warm up.
Turn the laptop on. By factory default the display should show on the external VGA monitor.

IF not;
There are at least 3 display options available,

A) Internal monitor of laptop ONLY
B) Internal monitor of laptop AND external VGA monitor
C) External VGA monitor ONLY

Hold the Fn key down, and tap once on the Display Toggle-Over key.
Which key is the Display Toggle-Over key?
Don't know. You didn't state the laptop manufacturer name, and model number.

It is one of the F keys at the top. F1 through F12.
Usually has a monitor symbol on it, and a side arrow.
(Most of the time the F4, F5, F7, or F8 key)

No display on the external VGA monitor?
Hold the Fn key down again, and tap once more on the Display Toggle-Over key.

Still no? Bad graphics chipset.

Display shows on external VGA monitor? Problem is the Video Cable, or in the Display Assembly.
Post back in a Comment after you have performed this procedure, and also post the manufacturer name, and model number.

If the graphics chipset is good, we'll go on with the diagnoses if you wish.

Regards,
joecoolvette

Jul 14, 2012 | Computers & Internet

1 Answer

I have omron arm blood pressure monitor, wehre in Digital display - numbers are not showing properly. It gets cut. where should I get it repaiers i Ahmedabad, India. Or what is the solution to get it...


I HAVE A OMRON MANUAL BP MONITOR MODEL HEM 432C. THE DISPLAY IS NOT COMING PROPERLY. I WANT TO GET GET IT REPAIRED. PLEASE LET ME KNOW THE NAME AND ADDRESS OF THE DEALER IN THANE OR MUMBAI.

Oct 11, 2010 | Omron Automatic Blood Pressure Monitor...

1 Answer

Machine is running but after a few minute there is no display screen shows black in mercury motherboard PVM7 pro model. I install 2pcs new ram (1GBX2) but machine shows each slot 512mb instead of 1gb...


Any beeping if there is
CPU cooling fans seized of about to seize?
This should happen in 30 second for a thermo shutdown.
Reseat the cpu make sure there is thermo white compound between the heat sink and Top of the CPU
make sure there is proper flat seatin of the heat sink and CPU make sure the fan is working.

It can be ur video or monitor,

Aug 26, 2010 | Computers & Internet

3 Answers

Need the specs and manual for a Foxconn LS-36 mobo dont know what northbridge it has its a478 socket it has three pci slots it was given to me,since I have a spare 478 processor


That mobo appears to come from a dell optiplex 270

http://www.motherboards.org/mobot/
http://forums.techguy.org/hardware/440110-dell-mobo-help.html

Sep 10, 2009 | Computers & Internet

2 Answers

NO SIGNAL PROBLEM


Please check whether the monitor is set to the correct settings. If you feel its incorrect, most LCD/TFT monitors come with an auto set up button which will restore the display to one that usually works. In case it still doesnt work, you might need to connect your pc to a different monitor and check the display settings. You could also try to download the drivers for this monitor and then re-connect the monitor and see if it works.

Jun 02, 2009 | ASUS VW192S Monitor

2 Answers

My problem is dtc p0402 I fail the inspection stiker because of that, my car is a 1997 mer- cury sable 3.0L engine V6


Try removing your EGR valve & cleaning good with throttle body spray cleaner, as well as clean hole under it. Re-install with new gasket & try. If that doesn't work, you may have to replace it.

Mar 27, 2009 | 1997 Mercury Sable

2 Answers

My Pc wont boot no signal in my monitor Help!


May be your in second HDD, you didn't set the jumper up. There are some more settings you will have to configure in the BIOS menu. in the BIOS, you should set the primary HDD as the master and the second(newer HDD) as the secondary. Then it should boot without any problem but if the problem persists I don't know what to do next.

Mar 08, 2009 | Abit IP35P Motherboard

1 Answer

Dont suit my mobo


remove the graphics card, turn the computer on, wait for any error beeps if any, then re-install the card , then try it again, this should work, hope this helps you,glen.

Dec 21, 2008 | ASUS A9550GE/TD Radeon 9550 Graphic Card

Not finding what you are looking for?
Mercury P4VM800M7 Motherboard Logo

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Computers & Internet Experts

Mark Gough

Level 3 Expert

415 Answers

Abhinandan  Patil
Abhinandan Patil

Level 3 Expert

569 Answers

Alun Cox

Level 3 Expert

2678 Answers

Are you a Mercury Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...