Question about Broksonic CTVG-5463GVC 19" TV

1 Answer

Remote can't find a code that works for universal remote,. channel buttons are pushed into tv case and can not be pushed manually.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers
Re: remote

Pawnbrokers carry tv's just like yours for under 50 bucks, i'd go that method.........

Posted on Dec 28, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I dont have the origional remote to my 27AF44 toshiba tv and i need to get to video/tv mode. i need to know how to do that or what is the universal remote code for this tv?

Ur tv have manual button that said VIDEO on the tv frame bazel.Push that VIDEO button u will get into Video 1 or 2 modes.Tries the tv manual buttons Channels up or down buttons like a few times,some Analogue tv models will let u to get into Video modes that ways.Not try website like to buy the tv original remote to used.This video modes funsctions are optional for tv useages for most or all of the tvs universal remotes.Tvs universal remotes are basicly only work for like for a power buttons on/off,channels up/down and volume up/down that it not more.

Aug 19, 2011 | Toshiba 27AF44 27" TV

1 Answer

While moving my parent's Curtis Mathes Cm19001 TV produced in 1999, I touched the channel button which took the TV off of channel 3. We've tried to use the channel buttons to return to channel 3,...

I have one of this tv model too.Just used a RCA component cables like Y,R,W hook one side to the tv Video IN INPUT holes and the VCR the other end of the cable to VCR Video OUT INPUT holes.Now just pushes a channel manual button up or down a couples for the tv go into VIDEO Mode.Play the dvd player it will work.Or try to buy a tv original remote.Return the universal remote.

Jun 18, 2011 | Curtis-Mathis CM19011 TV

1 Answer

Same problem as above.Disney p1310ATV lost the remote. No Phone # in orginial manual.Television system NTSC (American TV Standard) I have tried other universal remotes also I have a Sony RM-V210 universal...

there may be a problem with the tvs remote sensor. most universal remotes you dont even have to enter any codes you just have to follow the same steps to enter the code but instead of entering a code all you have to do is press the channel up button after following all other steps, just keep pressing up until it turns the channel on the tv then press enter or similar button after it changes the channel and this should lock in the code without entering a specific code.And if all other remotes only half the buttons work on if it happens with every universal remotes then it probably a problem with the remote sensor or the tv . Good luck too ya!!!

Jan 02, 2011 | Disney 13" TV

1 Answer

Can't find the input/video channel for my Emerson TV

universal remotes are tricky, if you have the pamphlet, often times there are several codes for each brand. you have to try all the emerson codes for your universal even tho the power, volume and channel functions may work with several emerson codes, some of these specialized buttons (like input) may only work on your TV with one specific code.

also, if there are any unlabeled buttons on the universal try them with each new emerson code.

Feb 11, 2009 | Emerson EWF2703 27" TV

4 Answers

Dish network remote code for Disney 13" TV

On your dish remote, press and hold the tv button until all 4 buttons light up, then release. push either of the power buttons once. Now start pushing the down channel button, It's the one right below select, continue pushing it until tv turns off. When tv goes off push down button one more time then push up button, when tv turns back on stop and press # key, tv light will flash 3 times and should be set. Note....if u press down button and tv does not turn off after going through all codes( tv light will start flashing) press cancel and try again only channel up this time. hope this helps.

Dec 31, 2008 | Disney 13" TV

3 Answers

Toshiba 24AF44

You need the original remote controller to be able to switch input modes.Universal ones usually don't work. If you don't have the original remote and can't find it ever or if it is too expensive you can buy an rf modulator ( very cheap) and connect your dvd player, game console etc) to the modulator then connect the modulator to your antenna with a coax cable. This worked for me. It placed the connection to channel 4 and other cable channels are still working,

You can buy the RF Modulator from:

Mar 16, 2008 | Toshiba 24AF45 24" TV

1 Answer

Need RCA univeral remote control code for Magnavox 27MS343S

Push in and hold code search button until it stays lit, then pushed the TV button, it flashes quickly. Then hit the number zero once, then hit channel up button until tv finally changes channel. Hit the mute button once to get it to store the code.

Feb 20, 2008 | Philips Magnavox 27MS343S 27" TV

1 Answer

How to use Toshiba 32D46 32" TV with Comcast 3 in 1 Universal Remote Control

Most univ. remotes have a search mode if code entry won't work-
Do you have the comcast instructions ? Something like.....
1) Tv power on
2) Push set-up or program on remote
3)Touch tv button on remote
4) Point remote at TV and push power off. Repeat until TV turns off.............then
5)Push enter to save....

Hope I helped you........T.

Nov 07, 2007 | Toshiba 32D46 32" TV

3 Answers

Tv is locked

I had the exact problem...tried a number of things that did not work. My dog "ate" my original remote. After reading your solution I took the universal remote that was programmed to work with the tv and tried holding down each button for a few seconds hoping that one would work like the display button on the original remote. It worked. I have a GE universal remote and the menu/info button worked for me. Again, you need to hold it in for a couple of seconds. Thanks for the help and I hope my added solution helps other people. Claudia in Minnesota

Feb 15, 2007 | Haier HTF20R21 20" TV

2 Answers

Cant change channels

Your in the video mode so you have to change the input. On the original remote, its the button left of the power button. A universal may not work for this. If you need the original remote, Its available at Good Luck

Aug 18, 2006 | Sanyo DS31520 31" TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Broksonic Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

66623 Answers

Cindy Wells

Level 3 Expert

4722 Answers


Level 3 Expert

57192 Answers

Are you a Broksonic Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides