Question about Maytag MAH2400A Front Load Washer

3 Answers

Problem with Maytag MAH2400 AWW

The washer starts correctly then after about 1 minute it will stop working and doesn't go past that stage. We tried different settings, hot cycle, cold cycle, etc. nothing seems to work.
Is there any one that can tell us how to run a diagnostic test on this washer?

Posted by on

  • 3 more comments 
  • WasherNewbie Jan 09, 2008

    Thanks. I will try this tonight, sorry about the delay in answering.

  • Linda328 Sep 16, 2008

    Mine was working fine, moved, hooked it up, goes on and starts with the water then 20 seconds later or so, it just quits!

  • angelawilco Sep 21, 2008

    Mine started and then stopped. It will not drawin. Now it sounds like a chain is clanking in it when I start it.

  • scottmorganb Oct 23, 2008

    mine wont spin. drains ok but will not start spin cycle

  • Linda328 May 11, 2010

    Re: the MAH2400, at what point do you press the Temp/Spin keys, before you press start or after start when water starts and then quits?

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

As for the user whose machine will not drain and sounds as though a chain is clanking, the solution is probably a coin caught in the drain pump. I just had the same problem. Access the pump from the bottom of the machine. 4 screws hold the mounting bracket on undo those, the electrical connection and two hose to the pump. Undo three screws holding impeller to motor and coin can fall out. Examine for damage if it is not too tore up, put back together. Keep in mind that when you unclamp the hoses that water will come out.

Posted on Feb 13, 2009

Ad

For the MAH2400 it is the Temperature and Spin key for 3 secs.

Posted on Oct 26, 2008

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,294 Answers

Works for Hotpoints:

Try the "on" & "start" buttons together for 10 secs or more. To get back to normal, do the same.

Posted on Dec 29, 2007

  • prem mathew Jan 12, 2008

    If helped u will pl rate me!!

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Maytag Front load Washer. "SUDS"


Clean the drain pump basket. http://www.youtube.com/results?search_query=kenmore+elite+front+load+washer+drain+pump+cleaning&oq=Kenmore+Elite+Front+Load+Washer+drain+pump+clean&gs_l=youtube.1.0.33i21l2.425000.427123.0.432800.6.6.0.0.0.0.410.1517.2-5j0j1.6.0...0.0...1ac.1.lQhVllMwg9M

Jan 27, 2013 | Maytag MAH2400 High Efficiency Front Load...

1 Answer

I have a Maytag Ensignia model MAV2757 AWW. The washer basket doesn't balance, even with a small load, and turns off due to the weight being unbalanced. The springs are there and oiled, the hardware...


Snubber ring that tub and spin basket assembly sits in is most likely worn. Very inexpensive part but extensive labor involved. I would suggest calling a competent service tech.

Nov 14, 2017 | Maytag Ensignia MAV2757AWW Top Load Washer

1 Answer

The door on my Maytag MAH2400 will not unlock. I have tried shutting off power to no avail. There is a throw rug in the washer that looks like it is caught in the door. Is there a manual release that...


Sorry no theres not,And when you get the throw rug out do not put these in there they do a lot of damage they can clog the pump.First thing try pushing the start button agin you well have to do this several times the machine has to drain before the door opens,when it open up.put draino-max and let it stand for 1-2hrs and run machine no clothes.And no more throw rugs

Jul 04, 2010 | Maytag MAH2400A Front Load Washer

1 Answer

Maytag toploader washer fills up with water correctly, then waits several minutes to agitate, then stops for a few minutes then starts, also it only works in the delicate cycle.


Hi,

Maybe the water doesn';t fill fast enough/drain fast enough so check all the filters.

maybe the heater is damaged or something is getting stuck somewhere now and then so to say, so it might just need some oil.

maybe a part of the chipset is failing.

maybe a valve in the water circuit fails.

i'd say you try to contact a technician and have him check it out.

I hope this is useful, and greets,

Olivier.


Oct 21, 2009 | Maytag PAV2300 Top Load Washer

1 Answer

Door broken at hinge area on Maytag front load washer 24".


Try using some J.B. Weld on it instead of glue. It will essential form a weld and should hold up better. You might want to give that a try. Good luck and best wishes.

Aug 04, 2009 | Maytag MAH2400 High Efficiency Front Load...

1 Answer

Maytag 5500 AWW Turns off randomly shortly after starting


Check out the motor control board near the floor on the right side. These have a high failure rate on the Neptunes. Maytag redesigned both the motor and motor control board to be more reliable. While inspecting this board, you are looking for a blown 10 amp fuse and /or burnt electronic components. If you have either... then you will need the the new motor conversion kit which includes the new motor, new motor control board and the wire harness. What you describe are signs the motor control board is nearing its end of life...

The kit takes about an hour to install. See www.neptunewaxmotor.com for disassembly photos so you can inspect the motor control board.


Sep 24, 2008 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

Front Load Washer - Error F30


hI I HAVE REMOVE THE TOP COVER. YOU WILL SEE AT LEFT A PLASTIC ACTUATOR WHO MUST BE UNPLUG FROM ANOTHER PLASTIC PIN. JUST PUT IT BACK TOGETHER AND THE PROBLEM WAS GONE!

Jun 16, 2008 | Washing Machines

1 Answer

Washer make a loud squeak when the spinning stops


its the brake, just as long as it stops, dont worry about it, made a web page that has pics on how to replace the spin bearing on the maytag atlantis washer, after searching the net on how to, finding the manual, not explanatory, i decided to make this a simple 1 page web site, with lots of pictures, i hope this can help someone else in doing this job. since it would cost too much money for a repairman to do the job, better to buy a new one instead, i tackled the job. since it basically takes apart the whole machine, it might help others even if they dont have the spin bearing problem but other parts to replace,
http://www.geocities.com/maytagrepairwasher/

Apr 06, 2008 | Maytag Atlantis MAV6451 Top Load Washer

2 Answers

Maytag SAV 2655 AWW prblems?


take a look at epinions.com for this model

seems almost everyone's had problems with it

Nov 17, 2007 | Maytag SAV2655A Top Load Washer

Not finding what you are looking for?
Maytag MAH2400A Front Load Washer Logo

668 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

588 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...