Question about Sharp Aquos LC-42D62U 42 in. LCD HDTV

1 Answer

No Picture I hit some button on the top and it changed the channel to 2-ANALOG. I switched it back the INPUT4 which has always worked and now no picture. When I try View Mode, it says view mode has not been selected. There is no drop down list anymore either. Any ideas>

Posted by on

1 Answer

Re: No Picture

Sharp 42" lcd. TV accessed incorrectly. Resulting in no picture.
Using TV remote, changed from analog 2 to input 4. Turned off TV remote. Returned to satallite remote, turned on TV, turned on satallite, still no picture. We seem to have power but no satallite signal. Ist time users of satallite TV.

Posted on Jan 06, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I am trying to get a picture on my tv. Since it was hooked up to a satilite receiver prier, I think the problem is the tv is still on Digatal instead of air/antenna. But I do not know how to bring up...

You will need the remote that comes with the tv if there is no menu button on the tv itself to bring the menu up. Hit the menu button and will want to go to the channel option and change it from digital to analog or even just scan for new channels. But honestly, when working with a satilite box you will usually not use your cable or antenna jack in the back of the tv so you might just need to change the input of the tv to get your channels up.

Sep 08, 2011 | iLO Flat Panel Televisions

1 Answer

Can set up th remote control for this tv with the direct tv cable remote

Here's how to scan for TV codes on your DIRECTV remote

1.Make sure your TV is turned on.

2.Slide the mode switch at top of remote to "TV".

3.Press and hold the MUTE button. This is located above the number 1 button.

4.While still holding down MUTE, press and hold the SELECT button until green light at the top of the remote flashes twice.

5.Then enter 991, the green light on remote should flash twice.

5b. Press 1 again (it will flash twice again), then you press the power on button at the very top right.

6.Point remote at TV and press CHANNEL UP button. Tap the CHANNEL UP button repeatedly until the TV powers off.

*If you hit channel up very fast, you risk going past the code. Pressing channel down will back it up. I alway hit channel up very fast till the tv turns off, then back it up slowly till it comes back on.

7.When the TV powers off, press and release the SELECT button.

*Note: If the green light flashes three times before TV responds, then all codes have been cycled through. Our remote controls are guaranteed to program to your DIRECTV receiver, however your TV may not be compatible with our remote control.

Mar 05, 2011 | Curtis LCD2425A TV

1 Answer

With my Sony Bravia 46" xbr the screen keeps cutting out. I'm usig hdmi cables and can't find a reason why te tv keeps cutting out. The sound still remains but picture doesn't. Not even out technician can...

Usually this happens to my set when I am in HD cable channel mode after being on a non-digital ANALOG channel.

I basically reset the TV by changing to a DIGITAL cable channel -- stay on that channel for ten-twenty seconds -- then I switch back DIRECTLY to a HD channel (key in channel number directly on remote).

TV works fine -- seems to be a glitch when the TV changes modes from Analog to HD

Jun 29, 2010 | Sony BRAVIA KDL-V32XBR1 32 in. LCD HDTV

1 Answer

Change channel, lose picture. power off/on, picture appears

switched HDMI plug from HDMI1 to HDMI2 port and that solved the problem

Oct 11, 2009 | Polaroid Flat Panel Televisions

1 Answer

Hdtv picture freeze

I also have a Brand new Sony Bravia 52" LCD with Comcast Cable (motorola box).When switching between HD Channels sometimes the left side of the screen shows a smushed version of the new channel, and the right side is a frozen picture of the previous channel. I correct this by switching to a non HD channel and back. Cable or TV problem I wonder?

Jul 03, 2009 | Sony BRAVIA XBR 52 in. LCD Flat-Panel HDTV

1 Answer

No sound on analog channels

Grab your sharp remote and press MENU, arrow over to SETUP, arrow down to RESET and press enter and follow that prompt to reset the unit. Once that is complete turn the tv off and unplug ONLY the tv for one minute then plug it back in. Then turn the tv on and see if you have channels, if you do, your audio should work on you analog stations, if you have no channels and all you see is a snowy picture do the following press MENU, arrow over to SETUP...arrow down to CH SETUP and press will then be at a screen that says AIR/CABLE, press ENTER, select CABLE or CABLE(STD) if that option is available to you. after then, arrow down to CH SEARCH, press ENTER, then you should be highlighted on ANALOG AND DIGITAL ENTER and wait for 15-30 minutes ( or until you get a picture back) and make sure you DO NOT press any buttons or turn the tv off and you should be good. good luck 2 u

Feb 10, 2009 | Sharp LC-32SB24U 32 in. LCD TV

1 Answer

Sanyo LCD

Try to re-program your tuner (search for channels). There are a lot of changes going on with service providers.
I am a servicer, and I have had to reprogram many sets because the local cable company just recently switched there services from analog (NTSC) to digital (ATSC).
Your problem might possibly be an internal problem, but most likely related to the aforementioned.
Having said that, there's always a possibility that a problem exists with your service providerw
If the above, reprogramming channels, doesn't work, then call your local cable or sattelite service provider. If that doesn't work, next person to call is your repair tech. Especially if it is under warranty.
Certified TV

Jan 09, 2009 | Sanyo DP32746 32 in. LCD Television

5 Answers

Picture shifts to left

I had the offset left issue for non-HD channels with my Panasonic 42" plasma, using Comcast HD cable box. Went into the configuration menu (to get there with the newer Comcast boxes, you have to turn the box off, then hit the menu button on the box immediately after). You will see on the menu a resolution (probably says 1080i), then below it a "4:3 override". Our said 480i. When I changed it to "none", so that it stayed 1080i, it worked! It also works by selecting 480p, but then the picture is stretched.

Mar 13, 2008 | Vizio P2 42 in. HD-Ready Plasma Television

Not finding what you are looking for?
Sharp Aquos LC-42D62U 42 in. LCD HDTV Logo

359 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Flat Panel Televisions Experts

The Knight
The Knight

Level 3 Expert

66499 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Dave Naylor
Dave Naylor

Level 3 Expert

834 Answers

Are you a Sharp Flat Panel Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides