Question about RCA D52W20 52" Rear Projection HDTV-Ready Television

2 Answers

Power turns on then off 3 times then wont come on

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

This has happened to me twice. We had the warranty and thank God we did. The problem is in a $7 transistor and you probably need to call a repair shop. They worked on ours and it took about 20 minutes to replace the transistor. They take out the bad one and soder in the new one on the circut board inside the back of the tv. The total cost was nothing for us because of the warranty, but it came to $385 for labor and stuff. Again, this happened twice, one year to the date from one another. The repair guy finally installed a different brand of transistors and it's been fine since. He said that RCA makes some terrible transistors and he will not use them again. Try and get the repair person to use a non-rca brand transistor, because it will more than likely happen again if he don't.

Posted on Dec 30, 2007

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,030 Answers

If the idicator light flashes this indicates a processor shutdown. first thing a customer can do is uplug for 30 min and try again. This never works i must admit but it eliminate the processor lockup chance. Now if it still does this then you have a problem the processor has detected a cuircit failure and shut the set down for safety. This also tells you it not a "FUSE" since the procesor is getting power. The processor generates a error log that can be read by a technician and a computer. other than that all i can offer is check for loose connection and if you have any technician experence alway check horizontal output transitor. BE CAREFULL TELEVISION GENERATED DANGEROUS AND POTETIAL LETHAL VOLTAGES

Posted on Dec 28, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why Wont My Straighter Work??


1) check continuity if you have multimeter 2) try to plug in another power socket 3) check the the reset button if any on it

Feb 02, 2015 | Televison & Video

2 Answers

Red light flashing, tv wont turn on


need the model number of the panasonic and also how many times it is blinking. The blinking is an error code.

Aug 03, 2012 | Panasonic Televison & Video

1 Answer

Wont turn on


Bring it in to a repair shop to test if the power cord/charger is dead...

Jun 28, 2012 | LG Xnote RD400

1 Answer

Power wont stay on light blinks 3 times


your convergence ic are short
repair about 350

May 02, 2010 | Panasonic PT-47WX53 47" Rear Projection...

1 Answer

My sandisk mp3 is frosen on the meau and wont trun


1. Push the "Power" switch downward into the "Hold" position.
2. Press and hold the "Menu" and "Record" buttons at the same time until the device resets.
3. Push the "Power" switch upward all the way to turn it back on.
OR
1. Grab a steady hold around the device.
2. Push the "Power" upward and hold it there until it powers off.
3. Power the device back on by releasing the power switch and then pushing it upward again.
OR
1. Unscrew the screws on the back of the device (or simply push the lid off if it is a model without screws.)
2. Take out the batteries from the slot and wait until the screen goes black.
3. Insert the batteries the same way they were mounted and attached the lid again.
4. Push the power switch upward to turn on the device.

Oct 01, 2009 | SanDisk Sansa e250 MP3 Player

1 Answer

Tonner light wont go out


Hold the go button while you power on, when all 3 LED's are on release the go button.
Press the go button 2 times, when all 3 led's turn on solid, press the go button 5 times.
All done...

Sep 01, 2009 | Brother HL-2040 Laser Printer

1 Answer

My ps3 power wont turn on at all? i hit the switch but???


man i dont know what to tell you but to change your hard drive and and or get a new ps3 dude

Jun 16, 2009 | Sony Playstation 3 (PS3) Console

1 Answer

Game stuck wont turn on


Your unit may be damaged. Turn the unit off, unplug it, wait 30 seconds, plug in, turn on, press power button. 
If you have the same issue, call sony support for hardware repair.

May 06, 2009 | Video Game Consoles & Games

1 Answer

Wont Power up


when you turn it on does it go red, then yellow, then keeps blinking red

Unplug replug, hold the power button, rough it up a bit, try it all. turn the switch on the back on and off about 5 times this isnt fun but worth a shot too. check power cords for bad kinks in it as well

Aug 02, 2008 | Sony Playstation 3 (PS3) Console

1 Answer

Wont power on


bad power transformer in it maby blown fuse or main bord burned take look at all 3

Feb 03, 2008 | RCA D52W19 52" Rear Projection Television

Not finding what you are looking for?
RCA D52W20 52" Rear Projection HDTV-Ready Television Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75888 Answers

jason

Level 3 Expert

905 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...