Question about Nintendo Wii Console

1 Answer

Wii sprts bowling

Im trying to play the bowling on the wii sprts, and i keep getting the same message on the screen, hold down the button B, raise arm and let go, I am doing this, and the same message just appears again and again after releasing the button B.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 167 Answers
Re: Wii sprts bowling

All my friends have a bad habbit of doing this. Watch the instructional animation when it shows the instructions. This will help you. hold up wiimote hold B, keep holding B and swing back, then swing forward and release B button.

Posted on Jan 25, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I just put the internet on my wii and now when i turn my wii off the light is yellow, not red, and the area where you put the disc in keeps blinking blue.

This is because you have wiiconnect24 turned on. wiiconnect24 keeps your wii in a standby mode so that you can receive messages when you are not playing the wii. When the disc tray is blinking blue this means you have a new message. If you want to turn wiiconnect24 off go into the wii settings menu then wiiconnect24. If you just want to turn the wii off fully then when you want to turn the wii off hold the power button on the wii down until it turns red.

Dec 30, 2009 | Nintendo Wii Console

4 Answers

Cant get pass the "press A button" screen

Turn off for a moment, try again, reconnect your controller.

Since its brand new, you can get it replaced if that doesn't work, dont waste your energy on it, just get another one, free replacement / warraty. Im sure.

Sep 05, 2008 | Nintendo Wii Console

1 Answer

Wii problem - Can't get past Select Language screen

keep getting a error has occurred,press eject button and remove the disc,then turn wii console off and refer to manual cant get past this.

Dec 25, 2009 | Nintendo Wii Console

2 Answers

WII remote not working properly

Try this. It just worked for me. I actually didn't have to synch. After I unplugged the console and restarted, it worked.

    Try these steps!

  1. Turn the Wii console power OFF by pressing the POWER Button on the front of the console. Unplug the power cord from the wall outlet for a few seconds. After a few seconds have elapsed, plug the cord back into the wall outlet.

  2. Turn the power of the Wii console ON. When you see the Health and Safety screen, open the small flap on the front of the Wii console to find a red button labeled "SYNC." Press and hold the SYNC Button down for 15 seconds. This will clear all the syncs on the Wii, allowing you to get a clean start to begin the process described below.

  3. After holding the SYNC Button on the Wii console down for at least 15 seconds, you can now "re-sync" your Wii Remotes:

    1. With the first Wii Remote you wish to sync, remove the battery cover on the back of the Wii Remote to find a small red button just below the batteries.

    2. Press and release the small red button just below the batteries on the Wii Remote; the blue lights on the front of the Wii Remote will blink.

    3. Quickly press and release the red SYNC button on the inside of the white flap on the front of the Wii console (picture).

    4. When the Player LED blinking stops and stays lit, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
    5. This sync procedure (steps "a" through "d" above) must be followed for each additional Wii Remote added to the system.

Dec 30, 2008 | Nintendo Wii Console

2 Answers

Cant get pass the "press A button" screen

make sure your light bar is plugged in and in sight

Jan 16, 2008 | Nintendo Wii Console

1 Answer

Wii controller

I just got off the phone with a guy from Nintendo and he told me to hold the Wii-mote upside down and gently clap it several times (5 to 10) and then try again. I did the same thing, I accidentally gave the controller a light whack when playing baseball and it stopped working. There is a censor in there that gets stuck.

Jan 04, 2008 | Nintendo Wii Console

2 Answers

Wii remote controller not fully funtional

in baseball you have to hold it beside your head and in bowling you have to raise your WII control up and realese th B button(hold B button than do instruction)(not for the Baseball game)

Jan 02, 2008 | Nintendo Wii Console

1 Answer

Wii bowling

This will only happen when you are a beginner.... Once you have played a few games it will go away. If you are playing as a guest the bar will always be there.

Nov 18, 2007 | Nintendo Wii Console

Not finding what you are looking for?
Nintendo Wii Console Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nintendo Video Game Consoles Experts

Troy Gorman
Troy Gorman

Level 3 Expert

508 Answers


Level 2 Expert

567 Answers

Paul Layton

Level 1 Expert

57 Answers

Are you a Nintendo Video Game Console Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides