Question about Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher

1 Answer

Diplomat dishwasher keeps flashing E2 anyone know what this means

Posted by on

1 Answer

Re: Diplomat dishwasher keeps flashing E2 anyone know...

Dishwasher starts then goes to prewaash and beeps.When opened it flashes f2.

Posted on Jan 13, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Samsung dishwasher dms500trw. what does error code f3 mean. i just replaced the hose after e2 code now 2 weeks later i have f3 code?

Samsung DMS500TRW - > ... > Dishwashers > Freestanding > Samsung

Rating: 2.4 - ‎49 votes
2.4 out of 5 stars for Samsung DMS500TRW in Freestanding Dishwashers (page 2). ... The machine gives an E2 error and will not pump water out. I have to manually cup it out. ... F3 Error. 1 out of 5, reviewed on Sep 30, 2013. Purchased dishwasher in Jan 2012. First broke ... F3 what dose this code mean? Dell asked on ...

Nov 26, 2015 | Dishwashers

1 Answer

Our dishwasher gas fault e2 we have had alook and nothing seems to be different

What do you mean "gas fault e2"? Your dishwasher is powered by electricity; not gas. Or maybe you meant to type "has fault e2" - well, now, that's quite a different story. Still we would need to know the model number of your dishwasher to be able to look up what that error code means.

Mar 08, 2015 | Samsung Dishwashers

1 Answer

My diplomat ADP8352 started the cycl then stopped and was continually beeping. the three lights at the left hand side flashing. help???

Check the manual and see if it can diagnose the problem. Or you may need to have it checked.

Oct 26, 2014 | Dishwashers

1 Answer

Why does my Diplomat ADP 8902 dishwasher beep twice when i switch it on and the 4th wash program light flash and do nothing else?

Can I say thank you for the above advice. Hit the programme button 4 times and closed machine. Now running rinse cycle. Let hope it works afterwards. Will post ant let you know.

Nov 20, 2010 | Dishwashers

1 Answer

My Diplomat dishwasher ADP8352 keeps stopping

Switch off the machine at your plug end and switch ON.

Check incoming water flow. Check and fill rinse-aid liquid in the dispenser. Check dish washer salt dispenser and fill.

These are the only actions an user can try.

May 27, 2010 | Dishwashers

1 Answer

Diplomat adp8322 dishwasher has start button flashing 7 times and rinsne cycle light on what does this mean

This is stating that no water is entering the dishwasher.

My solution was to turn the power off at the wall and wait for 10 minutes.

Turned it back on. Pressed the Start button and held til it beeped and reset, then started as normal and all was fine.

Jan 02, 2010 | Dishwashers

1 Answer

Flashing programme lights


Thanks for using FixYa. That means the control sensed that the heater in the D/W did not operate 3 times in a row. So the unit locks out. First remove the kick plate and you may have to pull the unit out from under the cab, but check your heater. Use a meter to see if it reads open; if so orders a heater assay it will come with a new control replace it too. If heater checks good then press in sequence normal wash, heat dry, normal wash, heat dry, normal wash, heat dry three times within 6 sec and all the lights will come on then hit cancel. What that did is reset the control and clear that fault. Keep in mind that D/W does not heat its own water and incoming water temp should be 120. The D/W will maintain that temp. When starting your D/W first turn on your hot water till it gets hot then start your D/W this ensures your unit fills with hot water and not cold

Please do rate the solution and revert for further assistance.



Nov 22, 2009 | Dishwashers

2 Answers

Diplomat dishwasher adp 8322

i had same problem and have found that under the lower basket the connecting bar to the spray arm had become detached this can be reattached by inserting the two nozzles back into position and pushing down youll see what i mean ! however i have found i now have to do this after every wash ,am currently onto diplomat to rectify this completely , hope this is any use.

Mar 09, 2008 | Dishwashers

6 Answers

Error code E2 (with a picture of a wrench)

E2 means a problem with the fill. The wrench means to contact Hobart for service

Feb 27, 2008 | Hobart 29 in. AM15-1 Free-Standing...

Not finding what you are looking for?
Hotpoint 18 in. DC28 Slim-Line Built-in Dishwasher Logo

615 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers


Level 2 Expert

157 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Hotpoint Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides