Question about Dell M5200n Laser Printer

2 Answers

Paper has creases or is crinkled

Printing from the dell laser M5200 causes crinkled or creased print outs

Posted by on

Ad

2 Answers

1jknjk

Posted on Jul 21, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

We have had it worked on 2 or 3 times in the last six months and it is still doing the same thing.

Posted on Aug 26, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does paper keep creasing up


can I get a little more info what do you mean creases is it jamming or just coming out crinkled if it makes it through the machine check the guides and the paper type the tray is programmed for if it stops around the fuser and folds like an accordion replace the fuser

Aug 05, 2014 | Kyocera Office Equipment & Supplies

1 Answer

Hp laser jet P2035N has a crease down the center of the page as the paper exits it is actually slightly raised so the print is smearing


Check to make certain that the fuser unit is not damaged. Often a crease or dimple is caused by foreign material on the fuser roller or the fuser is damaged. If the fuser is damaged, look into replacing the device, it may be cheaper than repairing the fuser.

Jan 31, 2013 | HEWLETT PACKARD - LASER JETS New - Hp...

1 Answer

The printed page comes out creased from the top left of the page to the bottom right.


Download this manual >> http://www.mediafire.com/?i0y9iqnqu79ppcj Go to page #203(6-15) Paper Feeding problems (wrinkles or creases) and follow the troubleshooting steps.
Note: PDF manuals require the Adobe Acrobat Reader for viewing and printing. http://get.adobe.com/reader/

Sep 03, 2011 | Brother HL 5140 Laser Printer

1 Answer

My Konica Minolta bizhub C250 seems prints about every 10th page crinkled and crooked. I can hear it going through the machine and crushing a crease in the paper as it prints. The printed also seems to...


The paper may not be feeding straight out of the paper tray due to poor stacking of the paper in the paper cassette. try another paper tray or check the paper in the paper tray for folded over papers usually near the bottom. Also try feeding paper from the hand feed tray on the left side. This uses a different paper path.

Dec 07, 2010 | Konica Minolta bizhub C250 All-In-One...

1 Answer

When duplex printing I regularly get creased


Check the rollers for any mis-alignment. Try loosening them and re-aligning them again. It should'nt be too hard.

Dec 28, 2009 | Dell 5100cn Laser Printer

1 Answer

CREASED PAPER


Most likely this is caused by a bad fuser, which can be replaced. Depending on the printer model it might be more economical just to buy a new printer..

Feb 27, 2009 | Brother HL-2040 Laser Printer

2 Answers

Paper is printing but top edge of paper is creased and torn


It sounds like your maintenance kit is defective.
The excess oil leads me to believe that.

Jun 04, 2008 | Xerox Phaser 8200 Laser Printer

1 Answer

Printer only prints on the left side and wrinkles up the paper on the left side


Hi there it could be that the fuser or the drum unit has some sticky labels attached to it check these units also check the paper feed path as there may also be some obstruction causing the paper to crease and crinkle.

Hope I could help
Thanks J

Jan 17, 2008 | Ricoh Aficio SP-C210SF Printer

1 Answer

Printed paper is creased


First thing to check is try it with a fresh unopened ream of quality paper, paper with too much moisture content, drys out and goes wavy when it runs threw the fuser roller at rear (180 deg), otherwise it will be the fuser rollers themselves causing your problem, which means that you need to replace fuser assy

Dec 05, 2007 | Samsung CLP 300 Laser Printer

Not finding what you are looking for?
Dell M5200n Laser Printer Logo

Related Topics:

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dell Office Equipment & Supplies Experts

The Knight
The Knight

Level 3 Expert

75871 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

David Patricia James
David Patricia James

Level 2 Expert

108 Answers

Are you a Dell Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...