Question about PSC QS6000 Plus Handheld

1 Answer

Psc quickscan 6000plus

Entry too large message when scanning barcodes of 12 digits or above works fine when scanning barcodes of less than 12

email is 00449,

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 25 Answers
Re: psc quickscan 6000plus

That scanner has been constrained to accept a digit length of 12 or less .. probably IPC codes which are 12 digits in length.

Do you know the symbology of the barcode you are scanning? (i.e. UPC, EAN, I2of5, C3of9 etc).

Posted on Jan 05, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Quickscan 6000 will read not read programming barcodes

usually there is a laminated like square piece of paper that gives you 4 options to scan and one of them is auto

Jun 06, 2009 | PSC QuickScan 6000 Plus Handheld

2 Answers

PSC 6000 Plus not scanning

There are a few questions:

What kind of cable do you use?

What kind of computer?
Normal computer or Laptop?


When you recieve the scanner like new you always have to program it.

First you do

Reset to factory defaults.... Never do this with working scanners


you have to program it.

First the Connection type
and then if needed a computer type.

After that you usually have to scan a suffix.

This means when you scan a barcode it needs to do something after.

normally it doesn't give Enter after you scan.
That is what the suffix is for.

and then you scan additional symbologies to scan

Like Code 39, UPC A etc. etc.

It needs to be programmed with the manual you recieved.
if you don't have it you can download here.

go down in the list to quickscan 6000
and programming manual.

please don't print all the pages. only what you need.

If you need more help i will hear it.

good luck.

Jan 09, 2009 | Datalogic QuickScan® QS6000 Plus...

1 Answer

Problems with very small Barcodes

Default settings set a global limit of 4.

You can set the global minimum code length by following the instructions in the user manual on page 24:

1) Start
2) Set Global Min Length
3) Scan the number on page 303: I.e. '0' followed by '3' to set length to 3
4) Set
5) End

Jan 09, 2009 | Datalogic PSC QuickScan QS6500 Handheld...

1 Answer

Scanner won't read the barcode

you read the code base?
Try another computer, if it is the same, council liaison without base.Direct bluetooth.

Dec 17, 2008 | PSC Quickscan 6500 Handheld

1 Answer

I need an owners manual

You can download a manual (06656 User's Guide/Programming Guide) at the DataLogic site. They bought PSC in 2005.

If your cables are connected between your keyboard and PC, be sure to set up the correct Keyboard Wedge Parameters, beginning on Page 34, to allow connectivity.
I'd start by scannig barcodes "CE" and "ZA" to reset to default wedge values. If that doesn't work, I'd procede to sc an "CF" for PC=AT,PS/2.
Pages 36 & 37 address the Caps Lock issue, where the scanned value is in the wrong upper or lower case.

Have a nice day,

Jun 12, 2008 | PSC Quickscan GP5385 Handheld

1 Answer

GP5385 incompatible with EAN 13

Dear Akiong, Please try to reset your scanner configuration, using some utilities from it's manual book (usually available at it's case/box), restore it by scanning it to factory configuration,or scan a label that would enable all symbologies.

Aug 24, 2007 | PSC Quickscan GP5385 Handheld

1 Answer

Programming GP5385 to scan 20 digits

Dear Huygen, Please try to reset your scanner configuration, using some utilities from it's manual book (usually available at it's case/box), restore it by scanning it to factory configuration,or scan a label that would enable all symbologies.

Jan 19, 2007 | PSC Quickscan GP5385 Handheld

2 Answers

PSC QuickScan GP5385-104342 RS-232 / DOESN'T WORK!

I think the problem you all are having is that this model of scanner requires a "decoder" to work correctly. It is another box which goes in-line between the scanner and the RS-232 port or ps/2 port of the pc. I'm not 100% positive about this, but I am pretty sure this is the problem. You need to look on e-bay for a psc barcode decoder.

Dec 15, 2006 | PSC Quickscan GP5385 Handheld

Not finding what you are looking for?
PSC QS6000 Plus Handheld Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top PSC Barcode Scanners Experts


Level 3 Expert

18258 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Are you a PSC Barcode Scanner Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides