Question about Velodyne DPS-12 Subwoofer

1 Answer

How to connect pioneer reviever to velodyne subwoofer

Hi i have pioneer reciever vsx-1017txv-k and i am trying to connect it with velodyne subwoofer dps-12,please let me know which is the best way to connect them as there are too many different ways to connect,i am confused.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 151 Answers
Re: how to connect pioneer reviever to velodyne subwoofer

Look for the sub pre out on the back of your amp and connect a sub cable to this and next to the LFE or phono type input on the back of the sub ,if it has two inputs left and right pick the left side ,set the cross over to suit your system and speakers,if you are not sure set the cross over to 80 hertz,this is a thx standard.
hope this helps.

Posted on Jul 03, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My Velodyne DPS-10 subwoofer hums when you plug in the RCA cable. The hum increases in volume when you touch the rear metal panel.

You have to check the RCA cable to the sub woofer. The RCA cabe have two connections inside it, one is for gain and the other is for ground sheild. If the ground sheild is broken then there will be hum from the sub woofer and it will increase if you touch the ground (rear metal pannel is connected to the ground). Replace the cable and check it again.

Jul 17, 2011 | Velodyne DPS-10 Subwoofer

1 Answer

I have jamo sub200. I connect to pioneer vsx-rs320k audo video receiver. when I turn the volume of subwoofer to a higher value with the receiver, the bass sound becomes distorted and not satifieng to...

Do one thing set the control behind the sub. set the level and cutoff control at it half position. Set phase control at "0" position. Then test the sound. if you ate using tower speaker as front speaker then you have to set the position of phase control 180 ,

Apr 11, 2011 | Jamo SUB 200 Subwoofer

1 Answer

I just got a velodyne deq 10r, i paired it with 5

In the manual that was included with the unit, it covers the basics of this question.

It really is up to you and how you want the sub to work with your mains.

Try one setting and adjust to find what you like.

Nov 22, 2009 | Velodyne Speakers & Subwoofers

1 Answer

Velodyne subwoofer HGS12

Not able to help you in Brazil

Contact Velodyne via their web site

Jan 15, 2009 | Velodyne HGS-12 Subwoofer

1 Answer

Velodyne SPL-1000 II subwoofer only snaps, pops and hisses

Go to the Velodyne web site, look under the support section and check the service center listings.

Also you could try the place you purchased the unit.

Dec 30, 2008 | Velodyne SPL-1000 II Subwoofer

1 Answer

Bose 901 connection to Pioneer VSX-917v Receiver

any pre-out should work. i believe the bose have a rca jack connector for attaching to the receiver. look at the new receiver connection diagram. any output that is rca designed for use by a recording device will send a signal that the 901's can see.
always check the manual on both before connecting for any precautions.
good luck

Dec 28, 2007 | Bose 901 VI Main / Stereo Speaker

Not finding what you are looking for?
Velodyne DPS-12 Subwoofer Logo

Related Topics:

549 people viewed this question

Ask a Question

Usually answered in minutes!

Top Velodyne Speakers & Subwoofers Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1042 Answers


Level 3 Expert

4518 Answers

Carlos Jaen

Level 3 Expert

435 Answers

Are you a Velodyne Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides