Question about Tomtom ONE GPS Receiver

1 Answer

Pin cde can not find pin code for bluetooth pairing to my phone

Posted by on

  • 4 more comments 
  • rkd1 Jul 04, 2008

    I have a samsung sgh d900 and a tomtom one v4.



    But i cant seem to be able to connect it to bluetooth. it is looking for a pin tried phone pin but does not work.

  • eddie wagner Sep 08, 2008

    yes my phone will not pair up with tomtom .where do i fine the code.

  • ihecht Oct 09, 2008

    Have: Tomtom Go 910, unlocked iPhone (original, not 3G) used with Rogers SIM card.

    On the iphone - under "Settings" - "General" - "Bluetooth" - I swich it on, and under devices it shows "TomTom Go 910 Not Paired".

    I touch "TomTom ... Not Paired" and it asks for a PIN. I tried all combinations I could think of (0000, 1234, etc). After entering a PIN, I press "Connect" and it comes back with "Incorrect PIN for TomTom Go 910" (or no message at all).

    On the TomTom I go to "Mobile phone" - "...establish bluetooth connection..." - "...start searching...", and I get "No phones found ...".

    Can somebody help?

    Thanks & regards.

  • ihecht Oct 09, 2008

    Have: Tomtom Go 910, unlocked iPhone (original, not 3G) used with Rogers SIM card. Forgot to add: Software version 2.0.2 (5C1).
    On the iphone - under "Settings" - "General" - "Bluetooth" - I swich it on, and under devices it shows "TomTom Go 910 Not Paired".
    I touch "TomTom ... Not Paired" and it asks for a PIN. I tried all combinations I could think of (0000, 1234, etc). After entering a PIN, I press "Connect" and it comes back with "Incorrect PIN for TomTom Go 910" (or no message at all).
    On the TomTom I go to "Mobile phone" - "...establish bluetooth connection..." - "...start searching...", and I get "No phones found ...".
    Can somebody help?
    Thanks & regards.

  • Anonymous Dec 06, 2008

    i have the same problem. could anybody helb me please?

  • howardyates Dec 18, 2008

    I have the same problem. cannot locate manual and need PIN to pair phone with GO 910.

×

Ad

1 Answer

Try 0000

Posted on Dec 27, 2007

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I can’t download my iPhone 8 phone book into my 2012 Grand Cherokee Uconnect.


Turn iPhone Bluetooth On:First you want to make sure that Bluetooth is functioning on your iPhone. Click on the Settings icon from the iPhone desktop. From the settings screen click General to show the iPhone General Settings as displayed in the below image. Notice you can see if Bluetooth is on or off from this screen. General Settings screen you can click on Bluetooth to configure the Bluetooth settings. On the Bluetooth screen shown below click to the left of Off to turn Bluetooth On.
  1. Begin Uconnect Setup:Now that Bluetooth is operational on the iPhone you can start the Uconnect process. Click the Uconnect button on the rear view mirror to begin. The voice from the Uconnect system will ask you to verbally select one of the options from the menu. Once Uconnect asks for your input say "Setup" to begin the process of syncing the iPhone.
  2. Start Phone Pairing:Once you say setup in the above step the Uconnect system will list numerous options available from the setup menu. One of these options is "Phone Pairing" so when the Uconnect system asks for the choices from the setup menu say "Phone Pairing".
  3. Pair a Phone:In the Phone Pairing menu you can modify current entries or begin pairing a new phone. After Uconnect lists all of the choices you should say "Pair a Phone" to begin the process of pairing the iPhone.
  4. Uconnect Pin Code:The first step in pairing a phone is setting the Bluetooth Pin Code that authorizes that phone to pair with the Uconnect system. When asked for the Pin Code say any four digit combination such as "1 - 2 - 3 - 4". Uconnect will repeat back the Pin Code so you can verify it has recorded properly.
  5. Connect iPhone To Uconnect:After you have set the Pin Code for the Uconnect system you need to view the iPhone's Bluetooth Settings screen which you can get to following the steps in Step 1 above. Before the Uconnect system shows up in Bluetooth the Bluetooth Settings screen will look similar to the below where you may have other Bluetooth devices showing or not.After a couple seconds the Uconnect system will display as "Hands Free" as shown in the below image. Notice it states that it is not yet paired,,,,,
  6. Click on the Hands Free device showing in the Bluetooth devices list above. This will open a new screen as shown in the below image that prompts you for the Pin Code you specified in Step 5.

    Enter the Pin Code and then click the Connect button in the top right corner of the above window. This will pair the iPhone with Uconnect and take you back to the Bluetooth devices screen where the Uconnect Hands Free device will now show Connected as shown in the below image.

    After the device is connected you will be prompted by the Uconnect voice again so proceed to the below steps.
  7. Phone Name & Priority: After connecting the iPhone you will then name the phone and set a priority between one and seven. Name the phone anything you would like and if this is your primary phone set the priority to one so this phone always connects at a higher priority than any other phone.
  8. Verify & Test:Now have a friend dial your cell phone while you are in your car to see if the music volume lowers and the Uconnect voice tells you there is an incoming call from a certain number. To make calls you can press the Uconnect button and follow the voice prompts.
  9. The Uconnect system is a great way to safely use your cell phone in the car.

Jan 13, 2018 | Cars & Trucks

1 Answer

I have an Alpine CDE-SXM145BT car stereo. that will not play Bluetooth devices.


Have you had the battery removed at any time before this happened or been jump started ?

Apr 09, 2017 | Alpine Car Audio & Video

1 Answer

How do i get code for bluetooth


First make sure that Bluetooth is on on the CDE-143BT. Press and hold Audio/Setup (below and to the right side of the rotary encoder dial until you enter the Setup mode. Use the rotary dial to get to Bluetooth. Press the Search/Enter button (the center of the rotary dial). Then use the rotary encoder to go through the Bluetooth Settings menu. Press Search/Enter to toggle the current value. After Bluetooth is on, go to Visi M setting and make sure that it is on. Now, you need to go to the Bluetooth settings area of your cell phone when it is within range of the receiver. Tell it to pair with the receiver. Then when it asks for the code enter "0000". This code is hard encoded into the unit. See page 23 of the manual for the CDE-143BT for the code. The manual is available here: http://vault.alpine-usa.com/products/documents/OM_UTE-42BT_CDE-SXM145BT_CDE-143BT_EN.pdf . Surrounding pages show setting the other Bluetooth settings.

Note: the receiver will be acting like a Bluetooth headset. That's why you need to enter the receiver's PIN on the phone.

I hope this helps.

Cindy Wells

Oct 10, 2014 | Alpine CDE-143BT Advanced Bluetooth CD...

1 Answer

How doI find my bluetooth pin


Bluetooth pairing with a vehicle and a cell phone will depend upon the phone type. Either the phone of the vehicle will tell you the code needed when pairing is in process. Many times, pairing doesn't require a code, especially if the phone is a "feature" phone and not a "smart" phone.

Sep 13, 2014 | Cars & Trucks

2 Answers

Need bluetooth code for eonon d2216


D2216 Bluetooth code/pin is 5802

Apr 14, 2013 | Car Audio & Video

1 Answer

Whatis the bluetooth pin for samsung c6112


check the bluetooth in settings go into bluetooth .. turn on bluetooth and phone will scan for devices to pair with. The other device will show if it has bluetooth on and set to discoverable.
Under available devices on your mobile touch with finger it will try to pair and say boothtooth pairing request. Confirm passkey is {whatever number it generates} to pair with {whatever device it is pairing with } note what the number is and press ok. At the top of the screen is a note says visable to all nearby bluetooth devices . the box needs to be ticked and other device should have same pass code when it tries to pair. It will ask you to confirm code.

Jan 12, 2018 | Cell Phones

1 Answer

How do you turn this device on and pair it with your phone?


to turn this device into pairing mode hold the power button down for 8 to 10 seconds,then a light should stay on.once you have put the bluetooth device into pairing mode you phone will find it and ask for a pin\pairing code.most bluetooth manufactures use a 4 digit pin\pairing code they are as follows ,0000,1234,9999,or 1111 and try them in that order one should work for you .Hope this helps

Mar 23, 2011 | LG HBM 730 Bluetooth Headset Wireless...

1 Answer

Bluetooth asks for pin


the phone is asking for a bluetooth pairing code. Usually 4 digits. It is printed in the owner manual of the device or headset you are pairing with the phone.

Try 0000 or 1234 or 0123

if none of those work, you must look up the pin code in the owners manual of the headset.

99% of the time 0000 is default pin code.

Good luck,
S

Feb 22, 2011 | Samsung S3500 Cell Phone

2 Answers

My RAZR V3 won't pair with 2009 Chevrolet Silverado bluetooth


http://www.gm.com/vc/bluetooth/index.jsp?brand=chevrolet&landing=true
PAIRING A PHONE WITH YOUR 2009 Silverado

Before you begin:

To take advantage of the Bluetooth for Chevrolet functionality, you must first pair a Bluetooth-enabled phone to a Bluetooth-enabled vehicle.

Note: If you do not pair a Bluetooth-enabled phone, all calls will be made using OnStar® Hands-Free Calling.3

Some additional tips:

1. You can pair up to five phones with your 2009 Silverado.
2. Your system automatically recognizes the first phone you pair. To use a different paired phone, you must
select it using the "Change Phone" command.
3. Only one paired cell phone can be connected to your system at a time.
4. When the vehicle is in motion, you cannot pair a phone.
5. Pairing should only need to be completed once (unless changes to the pairing information have been made, or the
phone is deleted).

PAIR YOUR PHONE

Set up phone - Turn Bluetooth 'ON':

1. From the main screen, select "Menu"
2. Select "Settings & Tools"
3. Select "Connections"
4. Select "Bluetooth"
5. Select "Setup"
6. Select "Power"
7. Select "On"

Set up vehicle - Enter 'Pairing' mode:

1. Press and hold the Push to Talk button for two seconds
2. Your system will respond with a "Ready" message followed by
a tone
3. Clearly say "Bluetooth"
4. Your system will respond with a "Bluetooth ready" message
followed by a tone
5. Clearly say "Pair"
6. Your system will respond with instructions and a four-digit
Personal Identification Number (PIN); you will need to enter
this PIN on your phone

Begin the pairing process on your phone:

1. From the main screen, select "Menu"
2. Select "Settings & Tools"
3. Select "Connections"
4. Select "Bluetooth"
5. Select "Hands free"
6. Select "Look For Devices"
7. Select "General Motors"
8. Select "Yes" to bond with General Motors
9. Enter the PIN code provided by the vehicle
10. Select "OK"

Finish the pairing process in your vehicle:

1. The system will prompt you to give a name to your phone
2. Say a name that best describes your phone (example: Corey's
phone); this name will be used to indicate which phone is
connected
3. Your system will ask you to confirm your name
4. If you confirm that name, the system will respond with the
message: "'<Phone name>' has been successfully paired"

Sep 04, 2009 | Motorola Mobility RAZR V3c Cellular Phone

2 Answers

Pin code


Is this the first time you are pairing two Bletooth devices ? Is the security pin for your Samsung phone '0000' ? Usually, the code you have to enter on your phone to pair it with a Bluetooth headset or headphones is '0000' (the number 'zero' 4 times), unless Jensen's Bluetooth headphones use a different pin.

Hope this helps.

zeceten@yahoo.com

Dec 22, 2007 | Audiovox WBT212 Headphones

Not finding what you are looking for?
Tomtom ONE GPS Receiver Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tomtom GPS Experts

LP

Level 3 Expert

489 Answers

k24674

Level 3 Expert

8074 Answers

Marvin
Marvin

Level 3 Expert

82313 Answers

Are you a Tomtom GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...