Question about Instant Cameras

1 Answer

Vivitar how do you load the film into the camera?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 619 Answers
Re: Vivitar

Be sure that nothing film inside the camera , open back side of camera by pulling spinning knob , put film spool on left side and at the right side insert the film strip on diagonal small hook, turn the spool rachet turning left side then click shutter twice while holding the spinning spool left side , then close the cover , tightened the spinning spool little bit then test shoot.

Posted on Jan 01, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I have a role of film w/ 15 shots and I need to finish the rest, how do I use it if it already been roled up

If the film has already been rewound into the cartridge then you need to use a film leader retriever to fish out the end of it again. You then load the film in the usual way and then in total darkness and without flash, fire the shutter 16 times and wind the film on between each shot. You need to waste an image to preserve those already on the film.

Note that you'll then have to tell the minilab operator what you've done: automatic processing equipment will look at the first few developed negatives to determine the frame spacing. When there's a gap halfway along the frame spacing will likely be out of register with the rest of the film, so you may end up with prints of half on e frame and half another. Also when the machine slices your negs into strips, it may cut halfway through some of the resumed shots. All this attention counts as special processing so may cost more.

But to be honest, the tool and the special processing is going to cost more than just losing the unused shots. Just get what you already have developed and printed and slap a new roll of film in the camera.

Feb 23, 2011 | Vivitar Instant Cameras

1 Answer

Positive goes up on the front or back ?

Pls. re-submit your question. Vivitar is not a KODAK and I'm not sure what you mean by positive goes up on the front or back ?

I hope by resubmitting under the correct brand and refrase the question that you will have a better answ. to the problem.

Hope I was of any help. :)

Dec 01, 2009 | Kodak Vivitar KV270 Film Camera

1 Answer

Can't open vivitar 5388

Use the rewind knob to rewind the film. Once the film is rewound, lift the knob up and the back should open. Then you can remove the film cassette and insert a new cassette and load the film.

Jun 11, 2009 | Instant Cameras

1 Answer

Vivitar Instant Slide Printer

I asked a friend who has used a Land camera how to insert the film.

Jan 04, 2009 | Polaroid OneStep AutoFocus Instant Camera

1 Answer

I need some general info on this camera's specs; i.e., film speed

Vivitar TL-125 was popular around Christmas 1988. Good to see your is still going strong!

In terms of ASA ratings, it would depend on whether the model has DX coding (which you would find as a set of gold pins in the bay where you put the film cassette.... If it has, then the asa range would be 50 - 1600 asa. If it hasn't, then Vivitar used to put a small selector on the baseplate of the camera to switch between 100 and 400 asa.

As a rule of thumb, I'd always use 400 asa film in this type of camera.... the extra two stops of speed far outweigh the loss of picture quality - especially with point and shoot zoom lenses.

I can't find a specific manual (no one seems to stockpile them), but if you can read a generic one, try the Vivitar point and shoot here :
(Note, I think you use a different sort of battery, but the controls and placings are all very similar between models).

If you need an original manual, then Oldtimer cameras will sell you an electronic download, or there is an original coming up on eBay in the USA in the next couple of days (with a camera - for spares). If you were really cheeky, you could ask the vendor to scan it in for you.

Hope this helps.

Nov 23, 2008 | Vivitar Instant Cameras

1 Answer

Vivitar v3000 slr instuctions

open the lever that you used to wind the film back in and pull up on it,it should pop open ,Rate me if it works!

Oct 10, 2008 | Instant Cameras

1 Answer

Film will not load

Took out the battery, then put it back in. The film then loaded properly.

Jul 21, 2008 | Kodak Vivitar KV270 Film Camera

1 Answer

Vivitar camera220/sl

Pull up on the little film windy thing at the very left. As far as it can go!

Oct 28, 2007 | Instant Cameras

Not finding what you are looking for?

Open Questions:

Instant Cameras Logo

Related Topics:

612 people viewed this question

Ask a Question

Usually answered in minutes!

Top Instant Cameras Experts


Level 3 Expert

93922 Answers

Steven Wander
Steven Wander

Level 3 Expert

574 Answers


Level 2 Expert

132 Answers

Are you an Instant Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides