Question about Sony Playstation 3 (PS3) Console

1 Answer

Cant connect to internet

I have a 40 mgb and have a belkin wireless router i have followed all directions but still no connection sometimes it says that the console found the adress and the internet but then it says i have to update my system when i do this it says theres an error with my dns what do i do

Posted by on

1 Answer

Re: cant connect to internet

I have the same fucking broblem man !!!

Posted on Dec 25, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

2 Answers

Netflix app

What is your download speeds for your internet? If your connection speeds are slow(Netflix likes around 10mbps) then you will have delay, or "Buffing" issues. To check your ISP's speeds, try this link I'm giving you on a PC.
Speedtest net by Ookla The Global Broadband Speed Test

Jul 04, 2014 | Nintendo Wii Console

1 Answer

I cant get internet acess so it told me to complain to you. :/

Here are step by step directions on how to set up your internet connection. Now the Nintendo Wii uses a wireless connection, so it's important to note here that you must have some type of wireless router, or internet connection that it can connect to!

Sep 04, 2011 | Nintendo Wii Console

1 Answer

Can't get into wifi with nintendo ds

You need to make sure you have wireless internet. If not you need to buy a router. The cheapest router is $40 at Walmart. You need to install the router to your main home computer giving you wireless internet access. Common routers are Linksys or Belkin. Hope that helps!

Apr 01, 2010 | Nintendo DS Lite

1 Answer

Connection problem for ps3 internet

cant you attach the old wireless router to one of the expansion slots in the new wireless router and have the old one for ps3 only and the new one for everything else

Dec 30, 2009 | Sony Playstation 3 (PS3) Console

1 Answer

Cant connect my ps3 psp go to the internet using

Check to see if your router has backwards compatibility to wireless G because the N router uses 256bit encryption coding while the G uses 128 bit encoding. PS3,and PSP use the 128 encryption coding also. If the router does not support 128 bit encoding you will never connect with it.

Nov 22, 2009 | Sony Playstation 3 (PS3) Console

1 Answer

I cant hook up my ps3 to the internet

Does the ps3 have wireless antenna to connect to router?

Sep 20, 2009 | Sony Playstation 3 (PS3) Console

2 Answers

PS3 cant go online with Belkin N150 (I think) wireless router

You need to disable the UPnP function on the Belkin router. Log into the router(, and look under System Settings for the UPnP function and disable it. If you haven't changed the password on the router, the default password is blank, i.e., no password.

May 30, 2009 | Sony Playstation 3 (PS3) Console

1 Answer

Wireless router wont connect

Hey mentalmc,

I had this problem at least once a month. Try these things out.
1. Make sure any WEP codes are entered EXACTLY as it is for your router.
2. Set up your router so only your PC connected to it can change any settings.
3. Turn off your PC while trying to connect via PS3 WiFi. The good ole Win update likes to download without you knowing it sometimes.
4. If all else fails, call Sony cause you may have a bad WiFi antenna or motherboard.

Jun 25, 2008 | Sony Playstation 3 (PS3) Console

10 Answers

PS3 cant go online with Belkin N1 wireless router

I have exactly the same issue as some of you above. As soon as I start my PS3 I manage to log onto the network for anywhere between 2 seconds and 2 minutes before I get the dreaded 80710102 error and have to reboot the PS3 to reconnect. I wrote to Belkin tech support and got the following reply... I Haven't tried it yet so don't know if it really works but thought I'd post it up here in case it helps anyone else out...

Hi Antony,

Thank you for contacting Belkin Technical Support.

We understand that the router does not support PS3. We apologize for the inconvenience caused.

A) To isolate the problem, please follow the steps given below to update the firmware and configure the router:

We recommend that you update the firmware from a computer that is connected to the router with an ethernet cable.

Please download only the relevant firmware on the router from the link given below. The firmware file would be according to the router version:

and save it to the computer.

- To update the firmware, log on to the router`s web interface by typing in in the address bar of the browser. The computer should be
connected to the router with an ethernet cable.
Note: If you have changed your Router’s IP address, use that IP address.
- By default, the password is blank. Click the "Submit" button.
- Click on "Firmware Upgrade" under the option "Utilities".
- Click on “Browse” and select the bin file that you have downloaded.
- Click on “update” and follow the wizard.
- After updating the firmware, restore the router to factory defaults by clicking on "Restore Factory Defaults" under "Utilities".
- Reconfigure the router.

Please follow the steps given below for configuring the router:

- Disconnect the computer from your Modem provided by your "Internet Service Provider" (ISP) if it is connected to the computer.

- Reset the router to "Factory Defaults". The reset button is found at the back of the router. The reset procedure is,

- Unplug the power cable and then plug it back again. Wait for 5 seconds.
- Locate the reset button (inside a hole) at the back of the router.
- Hold down the reset button till the power-light turns solid, and then release it.

- Connect the router to either the telephone line or the filter.

- Connect the computer to port number 1 of the router.

- Make sure the corresponding lights are lit. The telephone light should be ON and solid.

- Make sure your computer has a valid IP address by following the steps given below.

1. Click on “Start” -> “Run” -> and type “CMD” and click “OK”.
2. Type “ipconfig” in the black window and check the IP address.
3. It should be in the range of 192.168.2.x, where “x” ranges from 2 to 254.

- If it is not a valid IP Address, please assign a static IP address, "Subnet Mask", “Default Gateway" and "DNS Addresses" in the computer by referring to the link below.

- Please reset the Internet Explorer browser settings by following the steps below.

- Open Internet Explorer. Click on “Tools” -> “Internet Options”.
- Under the General tab, click on “Delete Files” under “Temporary
Internet Files” and select "Delete all Offline content" box.
- Click on “Clear History”.
- Under the Connections tab, select “Never Dial a Connection” and
click on “LAN settings”. Uncheck all the options and click on “OK”.
- Under the Advanced tab, click on “Restore Defaults”.
- Click on “Apply” and then “OK”.

- Log on to router setup page by typing “” in the address bar of the browser. By default the password is blank.

- On the left under “Internet WAN”, click on the option "Connection Type".

- Select “PPPOA”, (If it is ADSL)/ PPPOE (If it is DSL) and click on “next”.

- Type in the user-name and password and then re-type the password given to you by your ISP. Make sure you type in the full user-name.
For Example, the format for the User-name should be " or .net"

- Also confirm the settings of “VPI/VCI”, “Encapsulation” values from your Internet Service Provider (ISP) and configure the same.

- Change the “MTU” to “1400”.

- Click on “Apply Changes” button at the bottom. Wait till it saves the data.

- Click on Home on the right top corner and then click on the "Connect" button. You should be able to go online.

B) Configuration of PS3:

Please contact Sony and assign static IP address and DNS on the PS3. The static IP address should be assigned in the range of the router. For example: The IP address you assign should not be used by any other device on the network. Please confirm the ports to be opened for the PS3 from Sony.

1) Please follow the instructions given below to forward the port numbers for PS3 on the router:

- Please open the Internet Explorer and in the address bar type in "" and "Enter". The computer should be connected to the router with an ethernet cable.
- Leave the password blank and click on "submit".
- Click on "Virtual server" under the "Firewall".
- Enter the port number under "Inbound port" & "Private port".
- Enter the Static IP address of the PS3 under the "Private IP address".
- Check the "Enable" box and click on "Apply changes".

2) Please follow the instructions given below to enable UpnP on the router:

- Log on to the router web interface at
- By default, the password is blank.
- Click on System setting under "Utilities".
- Against the heading "UPNP Enabling", choose "Enable".
- Click on "Apply changes".

Note: The NAT feature on the router is enabled by default.

If the problem persists, please get back to us with the following information:

1. Type of connection provided by your ISP (Is it PPPOE, Dynamic or Static).
2. Name of the Internet service provider (ISP).
3. Version number of the router. You would find the version number on the bottom of the device. It would be a number in a series of thousands with a prefix “ver.”. Please confirm if the router is F5D8635?
4. Using the router, if the connection is stable on all the wired and wireless computers?
5. If the PS3 works fine with other networks?
6. When does the error come up? If it comes up for both, CAT5 and CAT6 cables?

Dec 06, 2007 | Sony Playstation 3 (PS3) Console

2 Answers

Wireless conection with xbox 360

does it have a firewall built in on the belkin?
im assuming it has a port blocked on the firewall settings.

Dec 02, 2007 | Video Game Consoles

Not finding what you are looking for?
Sony Playstation 3 (PS3) Console Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Video Game Consoles Experts


Level 3 Expert

3018 Answers

Troy Gorman
Troy Gorman

Level 3 Expert

508 Answers


Level 2 Expert

68 Answers

Are you a Sony Video Game Console Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides