Question about Zhone (6218-I2-200) Router

5 Answers

Changed router ip now unable to connect...

Hi I have a zhone 6218 and I was having a conflict with ip addresses (zhone and linksys were both set to 192.168.1.1) so I changed the zhone to 192.168.123.1 now I am unable to connect to the zhone (I get an ip address assigned to me) but when I enter http://192.168.123.1 into IE I instantly get unable to view webpage... I tried telnet also but telnet just sits there with blank screen no option to enter un or pw... Any ideas how to connect to router again? I can't restore defaults as it will erase stuff needed for tv (entone)

Posted by on

  • 2 more comments 
  • rcp2 Dec 25, 2007

    I have tried it direcly connected (hardwired and wireless) to the zhone. I am wandering if dhcp start address is 192.168.123.1 (router ip address)? opps if it is... whould this cause this behavior?

  • rcp2 Dec 28, 2007

    Thanks for the input, but I tried all that stuff before I fixed it, It had me puzzled big time, but what I did to fix it was I downloaded the config file off another router (same setup with tv and all) and restored defaults (held reset button on back of router) then connected to 192.168.1.1 as i did before and restored the backup config file i downloaded. Now all is well again... To fix the conflict I was having I changed the other routers ip as I can connect to it after changing it... It must be a bug in zhone router???

  • dcloake Feb 16, 2009

    I have a zhone 6218 dsl moden and I cant access the modem when I check using Ipconfig at the dos prompt I received the following info

    ip address:169.254.137.241
    Subnet mask: 255.255.0.0
    Default gateway: this field is blank

  • Anonymous May 02, 2009

    i have beetel 220 router. i have enabled access control management in router and accidenty deleted the IP which has access. Now i am not able to access the router web interface and i and my router reset button is not working. Please help me.

×

Ad

5 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi, i have the same problem that cannot connect to router after i changed ip address... i set my network connection to ip address 192.168.254.2 & subnet mask 255.255.255.0 & default gateway to 192.168.254.254... i can ping ip address 192.168.254.254 but cannot get into the web browser... i cant go back the router configuration page... pls. help... my router is zhone 6218...

Posted on Jan 18, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Cannot connect

Posted on Jan 07, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same problem..but this time..i changed the i.p address from advance setup under "lan" to 93.12.75.89..and now i cannot connect to the zhone router or internet..

Posted on Jan 17, 2010

  • gpm dree Jan 17, 2010

    i dont understand how yur suppose to do that...

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 428 Answers

The problem is y did u change in that way? U have to use same subnet address. Change Zhone's IP address to 192.168.1.X
Then another thing is disable dhcp from the router which is not connected to the PC.
Set the default gateway of the PC to the attached router. Set the attached routers default gateway to the router at the other end.
That will solve your problems.
Please rate the answer.
Thanks
:)
Goo Luck

Posted on Jun 16, 2009

  • Tharinda
    Tharinda Jun 16, 2009

    Check the IP address settings using ipconfig /all
    (using a command prompt)
    Then check settings and make sure u set the DNS address also. And make sure your IP address is not duplicated( not a problem if you are having a single pc)
    Cheers!

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 556 Answers

Try the configuration connected to the Zhone instead of the linksys.
You can probably configure both from the zhone yet only the linksys from the linksys. I believe routers expect configuration requests from their lan side ports and not the wan port.

Posted on Dec 24, 2007

  • 1 more comment 
  • david Dec 26, 2007

    When connected to the zhone do the following

    (assuming Windows XP)

    Start then All Programs then Accessories then Command Prompt
    Enter the following command (1 space after /)

    ipconfig /all

    In the resulting display you should see a default gateway address -- that should be the address of the router you are attached to. If it is not 192.168.123.1 as you expect -- it should give you access to the router.

  • david Dec 26, 2007

    If the above does not work statically address the Network adapter in the computer to avoid the DHCP issue and you may then get access to the router.

    Like
    iP Address 192.168.123.15
    Subnet Mask 255.255.255.0
    Default Gateway 192.168.123.1

  • david Dec 28, 2007



    Glad it is working now.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to open port on my 6218-12-200-0CC router for xbox live but dont know how


2 ways you can do this. <br /> 1. Connect to your router 192.168.1.1. Go to advance setup, NAT settings, then virtual servers. Click ADD, you will be at a setup screen now, click Select Service and choose xbox live. Then type in your ip address just below (192.168.1.1) and click save/apply, thats it.<br /> 2. Go to this site, <a href="http://www.portforward.com">www.portforward.com</a>, go through the motions and selct your zhone 6218 modem. Follow the directions they have listed.

Aug 08, 2010 | Zhone (6218-I2-200) Router

1 Answer

Can i connect a wrt54g wireless router to a zhone? to get wireless access on my laptop and wired connection to my computer?


s u can connect as u wish. connect a utp cable lan port of ur wireless router to ur pc. assign ip for ur pc with router's ip as gateway address. similarly search for wireless networks from ur laptop. u will find ur wireless router to in that range. click on it connect to the network. the ip gets automatically assigned for the laptop. Thats it u are done!!!

Jul 21, 2010 | Zhone (6218-I2-200) Router

1 Answer

Need to change the NAT setting on my Zhone 6218 DSL modem. How?


try these simple steps...

connect your computer to one of the LAN(wired) ports of router...
check the ip address and default gateway of your local area connection through control panel > network connections.... if you get the ip adress in the range of dlink router then try going to start > run > type "cmd" and hit enter >command prompt will appear... in command prompt type this


start iexplore(default gateway address) and hit enter...you will see the settings page of your modem.... go ahead and disable firewall and enable dmz for your ip address... also forward the ports that are necessary for your gaming device...

Jul 16, 2010 | Zhone (6218-I2-200) Router

1 Answer

Changed the IP address on Zhone 6218-I2, can't access browser UI.


Go to start -> run -> cmd.
When the window comes up, type: "ipconfig". The address that says "Gateway" should be the address of the router.

If that is too confusing, try the following combinations:
192.168.0,1,
192.168.0.254,
192.168.1.254
192.168.2.1
192.168.2.254

May 23, 2010 | Zhone (6218-I2-200) Router

1 Answer

I need help changing my mtu setting for my 6212-13-200 Zhone router


For that Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1
If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
Then click on WAN settings and change MTU settings then save settings and restart router.
Let me know if you need further assistance.
Thanks for using FixYa.

Mar 12, 2010 | Zhone (6218-I2-200) Router

2 Answers

Please help can u please tell me the ip address for a zhone router


IP Address for the Router is 192.168.1.254

connect the Zhone router to the Computer with ethernet cable

Click start - run - type cmd or command

in the Black DOS Screen - type ipconfig press Enter

it will provide you with IP Address (i.e Default gateway address)










Jan 08, 2010 | Zhone (6218-I2-200) Router

1 Answer

Can not access the router


Check the ip address on the computer.if your computer is not connected to the router then connect the computer to the router and try to open the setup.
when you check the ip address, you will see the default gateway number that is the ip address of the router.
click Here to know more about how to open the setup of router

Oct 29, 2009 | Zhone (6218-I2-200) Router

1 Answer

ZHONE 6218 unable to connect


Try to configure you router with WPA authendication. provide some encryption password,if asked. Then configure your lifebook with manual ip by wifi adapter ->network settings-> tcp/ip properties - > specify manual IP something like 192.168.1.2 Now try connecting to your router.It should ask for network key and will connect if key provided matches with the one configured.

May 21, 2009 | Zhone (6218-I2-200) Router

1 Answer

Great problem with router zhone 6218


i assume that you're not prompted with the log in screen. if so, you need to check if your computer is properly connected to the LAN/ethernet port of the router (Note: you need to use a hardwired computer if you want a stable connection while checking your wireless settings) and if it has a valid ip address which shoud be within the subnet of the router's ip address (Note: by default the router's ip address is 192.168.1.1 and "admin" is the default username and password)

if you're not sure of the current ip address of the router. go to command prompt and type ipconfig. it'll list there the default gateway which is the router's ip address.

now if you have checked that the computer has a valid ip address and it is properly connected to the router but you can't still access the router's page, there could be a program that is blocking the connection. try to disable any firewall or any antivirus programs installed on your computer.

hope this'll help you. you can click here for the manual if you would like to read some more about the router.

ciao!

Aug 13, 2008 | Zhone (6218-I2-200) Router

2 Answers

Zhone linksys router


hello!

-- who is your internet service provider
-- what is the operating system of your computer?
-- is this working fine before or is this a brand new router

i have read the same problem on the supportrix forum and you may try this and see if this help solve your problem. make sure your computer is directly connected to the router

Step 1: Shutdown the computer.
Step 2: reset the router while power on then Unplug the router’s power cable.
Step 3: Unplug the Broadband modem’s power cable and wait for 30 seconds.
Step 4: Plug in the Broadband modem’s power cable and wait for its lights to appear stable.
Step 5: Plug in the router's power cable once the modem’s lights appear stable.
Step 6: Power on the computer on and configure the router settings
Step 7: test the Internet connection.

if this still didnot work, upgrade the firmware of your router and repeat the same steps.
note:
configuring the router settings will depends who is your provider. if your isp is dsl you need to configure your ISP username (email address format) and password on the router. if your router is a cable no need to change any settings on the router. it should automatically work

Aug 06, 2008 | Zhone (6218-I2-200) Router

Not finding what you are looking for?
Zhone (6218-I2-200) Router Logo

2,297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zhone Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2268 Answers

Mike

Level 3 Expert

4356 Answers

Awesome12

Level 2 Expert

131 Answers

Are you a Zhone Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...