Question about Hobart 24 in. LXIH-3 Built-in Dishwasher

2 Answers

Water sprays out between the door and the sides during the wash cycle.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Check end plugs on wash and rinse arms

Posted on Dec 02, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 715 Answers

Check gasket

Posted on Oct 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After running a cycle, there is some water in the tub and the soap dispenser is open but the soap has only run down the inside of the door. It does not sound like there is a vigorous spray during the wash...


May have a stripped wash impeller. I would tear into the pump and look for any kind of obstruction but if its clean probably the motor assembly needs replacing.

Sep 27, 2011 | Frigidaire Dishwashers

1 Answer

White residue on dishes when the dishwasher cycle has completed, not sure why, salt is fine. Is this limescale?


Hi
Make sure that the water is being heated up by your dishwasher. Also need to make sure that the wash motor is spraying water around at full force.

Best way to check this is to start a normal cycle about 10 minutes into the cycle open the dishwasher door during the cycle. 1st observe if the water was being sprayed around as you opened the door. 2nd feel the water and see if it has heated up.
Reset or cancel the cycle and wait for the water to empty. make sure it is draining properly and also check to see if filter is clean.
I'm inclined to think your machine is not heating the water.
Ash

Sep 09, 2011 | Bosch 24 in. SHU43 Built-in Dishwasher

1 Answer

Leaks during wash and rince cycles


hi, Check your spray arm that nothing got stuck in its holes. make sure the spray arm is turning all the time when using the machine :
put the spray arm in 90 degree position, turn the unit on , open the door after few min check that the spray arm move...
make sure your seal of the door is clean and nothing prevent it to close evenly the door...
good luck 911servicetoday . com
I hope you find this Very Helpful and best regards!

Jun 25, 2009 | KitchenAid KUDR24SE Built-in Dishwasher

1 Answer

Water coming out of bottom during run cycle


Your lower spray arm is broken, allowing the water the hit the door where it shouldn't thus causing the water to blow out of the door gasket. To remove you turn the center plastic screw in the middle of the spray arm clockwise while holding the spray arm stationary. You can obtain the spray arm either at you local appliance dealer or at repair clinic dot com.

Feb 22, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Kenmore washer series 80, Clothes still soapy


If you are getting no water spray during the rinse cycle that would cause the soapy clothes issue.

Are you getting cold water during the wash/rinse cycles? If you have the machine set to warm/warm you may only be getting hot water while the final spin is calling for cold.

If you have cold water available then the timer is not calling for the water spray. The problem is either in the mixing valve or the timer.

Jan 10, 2009 | Kenmore 23822 Top Load Washer

1 Answer

Basin will not fill with water during rinse cycle but will agitate and spin.


most new washers have cold water only rinse and spray rinse ck cold water coming into machine during wash if no cold comes in suspect cold side of fill vale not opening ..could be wiring issue or a bad valve

Oct 24, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Dishes don't get clean. soap still on inside of door. . . water coming up to fill line and hot enough and dishwasher drains after cycle, spray arms are clear. . . help!


Water from the wash arms must be able to reach the detergent cup during the wash. It sounds as though the machine may be over-loaded during the wash and water does not cause the detergent to mix with the wash tank water. Try washing a cycle with nothing in the machine. Does the detergent still stick to the door?
If no, the machine is overloaded. Wash fewer items or smaller items so spray will contact detergent.
If yes, you have probably lost wash pressure. Clean all screens and jets.
Hope this helps,
Kermit

Aug 13, 2008 | Dishwashers

1 Answer

Lower spray arm


New Spray arm split around center joint so when it gets hot it opens up spraying water under door

 

take it back for another

 

Alan

Oct 13, 2007 | Hotpoint 23 in. BF50 Built-in Dishwasher

Not finding what you are looking for?
Hobart 24 in. LXIH-3 Built-in Dishwasher Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Dishwashers Experts

Jason

Level 2 Expert

211 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

handygirl911
handygirl911

Level 2 Expert

59 Answers

Are you a Hobart Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...