Question about Kenmore 24 in. 17462 / 17464 / 17469 Built-in Dishwasher

1 Answer

No lights are on as if there is no power. Kenmore

No lights are on as if there is no power. Kenmore dishwasher 17462

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 121 Answers

1st check for power at the incoming supply located behind the btm access panel. if u have a meter this can be checked. should have 110 volts if not u have an electrical problem, if u have 110 volts then id say your board may be bad. can turn off the breaker to the dishwasher wait 5 minutes then turn breaker back on, may reset board.

Posted on Oct 07, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Dishes on top rack always have food particles on inside. Have used the dishwasher cleaners, use liquid rinse, tried liquid and tablet soaps, have used different comdinations of cycles, "hot water, or...

Hi, I have an older dishwasher also and recently mywife also complained about it not cleaning right... so me being the man I amtried in vain to clean the things... Bought new spray arms online and installedthem in the thing works like new... However I have also foundthat if the heating element goes bad then that also can mess things up bad...So I would buy new spray arms, and also check out the heating element to makesure it is working... Here is a tip that will help you with the onlinebuying...
Dishwasher SprayArms not Spinning

How to Buy ApplianceParts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The HeatingElement not Working

DishwasherMaintenance DishwasherResidue and Film on Dishes


Asker's Testimonial "explanation very clear. will give it a go and see howsimple it was. thanks Ronnie " - ronnieshomes

Aug 02, 2011 | Kenmore 24 in. 17462 / 17464 / 17469...

1 Answer

Won't turn on

If the dry light is flashing you will need a new keyboard, if the clean light is flashing try this key dance

normal, heated dry, normal, heated dry

wait for the lights to come on and then go off, press cancel and wait 2 minutes, try a cycle. If it works and fails again let me know we can dig deeper to find out the root cause

Apr 24, 2010 | Kenmore 24 in. 17462 / 17464 / 17469...

1 Answer


Do you still have sound? Can you see light at the back of the set when the screen is blank -if so the bulb is ok and you've just lost video.

Oct 14, 2009 | Televison & Video

1 Answer

Has become very noisy during sensing cycle.

Either the motor is failing to pump water or there is too much soap in the system. Add 1/4 cup veg oil and run again.

Sep 24, 2009 | Kenmore 24 in. 17462 / 17464 / 17469...

3 Answers

Our Kenmore Dishwasher caught fire.

You may want to contact Sears to see if there was a recall on your model dishwasher. There were problems with the door assemblies on some model dishwashers that were caused by the rinse agent leaking into the wire harness of the door. Over time the rinse agent would corrode the wire insulation causing the units to catch fire in some cases. The fix was a free inner door and wiring harness upgrade kit from the manufacturer. Here is a link you can refer to that may offer some assistance:

Although I did not see your model number listed, you may want to call the Consumer Product Safety Commission number listed at the bottom of the page and report this incident.

I hope this offers some assistance to you.

Sep 17, 2009 | Kenmore 24 in. 17462 / 17464 / 17469...

1 Answer

Water doesn't heat up

The most common reason for no heating is the failure of the heating element which is located beneath the lower spray arm. Inspecting it for breaks and damage would be the first step. If you do not see obvious damage, after triple checking that poser is off to the DW, pull the kick panel from your DW and check where the heavy gauge wires connect to the two terminals of the heating element.

Please post back here with further questions or what you found, OK?

Dec 14, 2008 | Kenmore 24 in. 17462 / 17464 / 17469...

1 Answer

Clean light flashes on dishwasher

reomvethe lower acess panel under unit, ther shoiuld be a detailed techsheet for all sortsa problems and issues you come across.

Mar 22, 2008 | Kenmore 24 in. 17462 / 17464 / 17469...

1 Answer

How long is too long?

I doubt it. If the unit has a mechanical timer, it is binding. If the shaft cannot be cleaned up, it will have to be replaced. Typical times are 40 minutes to an hour, depending on the cycle.

Feb 17, 2008 | Kenmore 24 in. 17462 / 17464 / 17469...

Not finding what you are looking for?

Open Questions:

Kenmore 24 in. 17462 / 17464 / 17469 Built-in Dishwasher Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

Fred Sops

Level 2 Expert

272 Answers

D. E. Hev

Level 3 Expert

1175 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides