Question about Citizen Skyhawk Eco-Drive JR306059F Wrist Watch

Open Question

My Citizen Skyhawk AT Eco-Drive JY0000-53E Wrist Watch has stopped running. The analog hands have stopped moving, the left digital read out is blank and the right digital read out says ERR. How do I get past this?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: My Citizen Skyhawk Eco-Drive JR3000-51F Wrist

I had the same issue, and was able to reset it doing the following:

1. I let it recharge for at least a day in bright sunlight
2. I turned the selector to "CHR"
3. I pulled the crown all the way out.
4. I held both buttons down for 5 seconds (don't know if this was what did it.
5. I pushed the crown back in.

It did some funky hand movements stuff and then started off working.

Posted on Aug 27, 2009

slp11508
  • 43 Answers

SOURCE: Dead Citizen Eco-Drive

You need to expose this watch to sunlight for about 8 hours to let it recharge it's solar cell. Make sure that sunlight is shining directly on the face and not just "kind of" shining on the face. I put it in a window ledge where the sun beats down to make sure it gets the most sunlight possible.

Repeat this for a few days to make sure it's fully charged.

Posted on Jan 05, 2009

  • 1 Answer

SOURCE: setting time on my citizen eco drive skyhawk model jr3090-58l

I would like to set this watch for my son, and request help.

Bill

Posted on Sep 19, 2009

  • 13 Answers

SOURCE: I cannot set the date on my Citizen SkyHawk Eco-Drive

The watch will automatically set the time and date when it is in receive mode (Mode hand is on CAL, TME, RXS) Pull crown out 1 click, turn crown to put mode hand in the ORANGE zone. push crown in. Set on stable surface with the 9:00 position facing the direction of the atomic clock signal. Push and hold lower button for 2 seconds till it beeps. it will enter RECEIVE mode and in 2 -15 minutes it will (if there is signal) update time and date automatically. While in RX mode the lcd windows will flash between RC & RX, the second hand should show signal level between 1 & 3 hr positions.
Do NOT move the watch until it has resumed the one second sweep motion and made a beep.

Posted on Nov 08, 2009

gemineye61
  • 831 Answers

SOURCE: Citizen Skyhawk Eco-Drive JR3090-58L instruction

http://www.citizenwatches.com.au/instruction-manuals

You will need the calibre number on the back of the watch but try this citizen site.

Posted on Jul 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have the correct time set in the watch, the main analog clock shows the correct time, but the UTC analog hands19:00 when the UTC digital time is 12:00. How do I reset the UTC analog hour hands?


The hands are driven by the digital. It seems to me you have the wrong digital city. Please review the setting instructions for your Skyhawk at: http://www.citizenwatch.com/

BTW, I love my Titinimum Skyhawk

Aug 03, 2011 | Citizen Skyhawk Eco-Drive JR306059F Wrist...

1 Answer

I have a Citizen eco-drive blue angel watch and the hands are out of sync with the digital clock. Can you help?


Hi there. Your hands are driven by the digital. Please consider reviewing the instructions for setting at: http://www.citizenwatch.com/

If there is in fact a fault, please consider returning the watch to citizen for repair and adjustment.

Jul 28, 2011 | Citizen Skyhawk Eco-Drive JR306059F Wrist...

2 Answers

My Citizen Skyhawk analog UTC hour hand is alway 1 hour ahead of the UTC digital hour. I've tried reset and the hour/min hand alignment process without success. Any ideas other than sending in the watch...


You've gotta go to the set setting, one click out on the knob and cycle through all the timezones using the B button (the lower one) to change all the settings to OF (for winter) or ON (for summer time). According to their website FAQ, they can't determine when daylight savings time goes into effect for all the different time zones so there is no automatic changeover from SMT to normal and back again. Disappointing, I know. I just spent half an hour going through their website looking for some master switchover as well.

Mar 27, 2011 | Citizen Skyhawk Eco-Drive JR306059F Wrist...

1 Answer

Hello I've had my citizen Eco drive skyhawk watch for at least ten years now. I remember reading in my manual years ago that a battery needed to be replaced even though it's solar powered. My watch went...


There could be other issues beside the battery. My best solution would be to take back to where you bought the watch, or any other authorized Citizen watch retailer for repair.
This is Citizens web site:
http://www.citizenwatches.com.au/
Best regards,

Mar 16, 2011 | Citizen Skyhawk Eco-Drive JR306059F Wrist...

2 Answers

Citizen Eco-Drive Blue Angel Watch C650. I can't get the analog to match the digital. i have reset everything to the O positon. Reset time, calendar.


Click on my profile (escapement), then click on Tips and Tricks. There you will find link to all citizen watch manuals. Rate me, please.

Mar 02, 2010 | Citizen Skyhawk Eco-Drive JR306059F Wrist...

1 Answer

My Citizen Skyhawk Eco-Drive JR3000-51F Wrist Watch has stopped running. The analog hands have stopped at 12:00 and the left digital read out is flashing UTC and the right digital read out is flashing...


I had the same issue, and was able to reset it doing the following:

1. I let it recharge for at least a day in bright sunlight
2. I turned the selector to "CHR"
3. I pulled the crown all the way out.
4. I held both buttons down for 5 seconds (don't know if this was what did it.
5. I pushed the crown back in.

It did some funky hand movements stuff and then started off working.

Aug 02, 2009 | Citizen Skyhawk Eco-Drive JR306059F Wrist...

1 Answer

I can't get the clock hands to correspond with the digital time.


You must set the "Zero" position for your watch. Follow the instructions at this address and your problem should be corrected.
http://www.geocities.com/watch_crazy/skyhawk/setting/setting.htm

Good Luck

Jun 18, 2009 | Citizen Skyhawk Eco-Drive JR306059F Wrist...

2 Answers

I cannot set the date on my Citizen SkyHawk Eco-Drive


Just pull the crown out, turn it so that the bottom analog display is set on "CAL" and push crown back in. Voila!!

Mar 16, 2009 | Citizen Skyhawk Eco-Drive JR306059F Wrist...

Not finding what you are looking for?
Citizen Skyhawk Eco-Drive JR306059F Wrist Watch Logo

Related Topics:

1,971 people viewed this question

Ask a Question

Usually answered in minutes!

Top Citizen Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18391 Answers

Jimmy Accardi

Level 2 Expert

101 Answers

The Knight
The Knight

Level 3 Expert

74106 Answers

Are you a Citizen Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...