Question about Kenwood Car Audio & Video

Open Question

E-04 on kenwood KDC-2019 car sterio

My kenwood KDC-2019 car sterio works fine but when i put a cd in it will read it for a while then E-04 will show on the display.i have tried multiple cd's in it and they all do the same thing so i think it is not able to read the cd due to a dirty laser but how do i clean a laser in this player and what does E-04 mean.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MediaMan85
  • 163 Answers

SOURCE: cd player and hot (high temperature) CD's

As with all electronics... anything can happen (even unexplained). There are two things to think abou tin this expensive experience.

  1. 1.CD's are made of plastic and metal... excessive temperature can cause them to warp, but not as bad as the old vinyl.
  2. Mosy electronics have an acceptable operating temperature. Although the unit may work outside these limits, it is not recommended. ex:My Sony DVD R/W has a range of about 40-95 F. Being in Houston I am sure the upper limit is reached OUTSIDE the car. Inside you are probably pushing 120+.
It may not be convenient but if you have to leave discs in the car, try putting them in a case in the trunk, out of direct sunlight. And let things cool down inside the car before trying the CD player.

I have not seen this before but like I said, anything is possible.

MM85

Posted on Jul 21, 2008

Ad
  • 33 Answers

SOURCE: i need the wire colors and what they are for for

Here is a link to the manual which has the wiring and all the installation instructions in it.

http://inform3.kenwoodusa.com/manuals/KDC-205.pdf

Posted on Mar 04, 2009

  • 102 Answers

SOURCE: Display doesn't illuminate on flipdown faceplate

Has unit gotten very cold lately? If faceplate is removable, remove it and clean the brass terminals with a CLEAN pencil eraser, wiking sure to blow off any rubber "crumbs" when finished.

Posted on Mar 10, 2009

  • 1 Answer

SOURCE: protect apears in display of my carradio Kenwood KDC 3034

I did not resolve my problem and I defenitly am not going to pay anything to you to resolve it. So if you have the resolution to my problem tell me or do not bother to write to my email adres anymore. Thanks for your answer.

Posted on Jun 25, 2009

  • 182 Answers

SOURCE: I cant remove the demo mode off the screen of my

here is a pdf manual scroll down and it will show u how to do it just go to this link
http://inform3.kenwoodusa.com/manuals/KDC-MP3035.pdf

Posted on Jun 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It won't power on, the security light works when face plate is off


HI.. YOU MAY HAVE LEFT ONE OF THE POWER WIER UNPOWERD THESE STERIOS HAVE TWO .

Mar 30, 2014 | Kenwood KDC-MP2035 CD Player

1 Answer

Kdc-mp


put a cd cleaner in your cd player see if that helps.

Feb 16, 2014 | Kenwood KDC-MP435U CD Player

1 Answer

What cause the display to go out on the kenwood kdc-235 cd player


Hi there,

You could try reading my tip on repairing Kenwood faceplates.

How to repair Kenwood Faceplate


Cheers,

Jan 02, 2013 | Kenwood KDC-MP235 CD Player

1 Answer

Kenwood KDC-319 CD Player Logo Problem with KDC-319 CD Player installed a kenwood kdc 319 in a 04 chevy malibu when i have car off i turn deck on an my cars dash board lights turn on Posted by A


I would start by disconnecting the radio and hooking it up right,the power should go through the ignition switch.So that when you turn the car off the radio will go off and to hear it on again you have to turn the key to accessory or start it.That might take care of a few of your problems.

Jun 25, 2012 | Kenwood KDC-319 CD Player

1 Answer

WHEN I INSERTED THE CD IT SHOWS 'E-04'. HOW DO I RESTORE THE SYSTEM TO NORMAL? ..


E-04 errors are usually a 'no CD is loaded' problem. Your CD is too dirty or scratched to be read properly, or upside down. Clean/polish your CD, and reload properly.

Jun 27, 2011 | Kenwood Sirius KDC-MP225 CD Player

1 Answer

Cd error on my kenwood kdc-4024


Try pressing reset button, if that dont work your optic is faulty. cheaper to buy new cd player.

Nov 03, 2009 | Kenwood KDC-4024 CD Player

3 Answers

Kenwood car stereo cd player reads protect mode how do i fix this


i have a kenwood kdc-241 car stereo and it has gone onto protect mode i have done everything it says in the manual and even taken it out of the car just in case it was damp i have tried putting it back in but still is in protect mode can anyone help me please

May 25, 2009 | Kenwood Car Audio & Video

1 Answer

Kenwood KDC-MP438U reciever installed. No sound in any mode.


if its a newer truck it will most likely have a factory amp u either have to utilize or bypass

Apr 21, 2009 | Kenwood KDC-MP438U Car CD/ MP3 Player

2 Answers

When i hook up my ipod to my kenwood kdc mp728 i cant figure out how to play it through the radio


it should be in aux try to press source buton and see if that is an option if not an alternative is to hook it up on the back of the cd player in the audio in or aux or aux 2 using a wire adapter from walmart in the car sterio section

Sep 14, 2008 | Kenwood Car Audio & Video

1 Answer

No Sound - boat stereo


Assuming that the four speakers are connected to the amplifier, then the amp is the most likely problem component. Does the amplifier show a power light when the system is turned on? Note that there is probably another fuse in the amplifier power wire, near the battery.

Mar 16, 2007 | iLO XM-MP3-CD Car Stereo

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4869 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...