Question about Dacor Cooktops

Open Question

Western Holly gas cook top

Hello,

I have a Western Holly gas cook top. One of the burner is liking gas and needs to be replaced. CAn you advice me on a good repair company?
Thank you

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
Rotu
  • 175 Answers

SOURCE: gas cook top

Most of the time when I come out for a service call with this problem, it is usually because the burner cap is not seated properly on the base. Look at the burner and make sure there are no uneven gaps. Most of the time you will have to rotate the burner cap till a notch or pin "seats" into place. Most burner caps just sit on the bases, and so they get knocked off or moved when the cooktop is cleaned or installed. Hope this helps!

Posted on Oct 31, 2006

Ad
textonor
  • 130 Answers

SOURCE: Thermadore gas stove top - left 2 burners won't light

Either the potentiors or the simmer control.

Posted on Jan 06, 2008

  • 1 Answer

SOURCE: spark module will not stop after lighting burner

The module might not sense the flame: check electrical connections: wire (and its contacts0 and conections by fryer chasis; to be sure please bond with 18AWG wire pilot burner with spark module green wire.
MarKor

Posted on Mar 09, 2009

heatman101
  • 43501 Answers

SOURCE: Electric ignition for one burner on counter top ge

Hi,
Here is a tip that I wrote to help people troubleshoot problems with their cooktops not igniting.

Cooktop Range Stove spark ignition does not work
http://www.fixya.com/support/r5649407-cooktop_range_stove_spark_ignition_not

heatman101

Posted on Aug 18, 2010

  • 1 Answer

SOURCE: G.E Profile gas cook top #JGP640 ignitor.

I just moved into a house, have a G.E Profile gas cook top #JGP640, the problem is when I turn of the front right burner, the electronic ignitor doesn't turn off and make the other three sparking the same time and won't stop, driving me nut. I double check all ignitors are cleaned. What else should I check or should I just give up????

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change out the Switch on a gas cook top -Jenn-Air JGC9430ADS


if you mean the switch under the knob,
you can open up, drill, the switch and clean up and use it again, uless the copper parts are burned out.

to get to the switch, most likely have to unscrew all the screws holding the top and the bottom together, most likely the screws will be on the top, by the gas burner on each burner. and may need to check the sides for additional screws .

if you go step by step , its pretty easy.
maybe you should look up on you tube for demo.

Apr 19, 2013 | Jenn-Air Cooktops

1 Answer

2 burners wont ignite


Hello there:
A burner doesn't work The most common problem for gas surface burners is that they get gas but don't light. This is generally caused by dirt or grease splatters on the burner itself. Residential-grade range/stove burners are round and have small holes around their perimeter to allow gas to flow out and create a round flame. The gas coming from these holes is often ignited by a small vertical row of holes on the side of the burner. If these vertical holes are clogged or obstructed, the gas can't ignite. The solution is to clean the burners thoroughly. Use a toothpick to clear the small vertical holes, then allow the burner to dry completely and try lighting it again. If it doesn't light immediately, either repeat the procedure or call a qualified appliance repair technician.

Jun 29, 2010 | Thermador SGS36GS Gas Cooktop

1 Answer

All cook top burners spark when any is turned on


OK, the best action is to call for service, if the unit was just installed, and purchased. This unit should be covered at this time, by the manufactures warranty, or store 30 day warranty. This repair should be free. The culprit will be a faulty spark ignition switch, and module. Testing is required. Once this switch, or(module), is replaced, the unit will operate correctly.

Nov 04, 2009 | Jenn-Air JGC8430 Gas Cooktop

1 Answer

Cook top burner knobs all 4 not able to turn


Hello,

Just to be clear, non of the 4 burner controls/knobs will turn ? You are familiar with this unit are you ?

Typically you must push down and turn to activate them.

Let me know if that is not the solution.

Good Luck :)

Oct 29, 2009 | Gaggenau 23 in. KG 260 Gas Cooktop

1 Answer

I cleaned the gas top and the two left side burners do not ignite


Take the burners out, then take a needle and stick in the small hole where the gas comes thru.

Jul 15, 2009 | Maytag MGC5430BDS Gas Cooktop

1 Answer

My ignitor on my ge cooktop keeps clicking slowly in off mode


As it relates to 5 burner gas cooktop Model Number JGP 963SEJ1SS
First - Ignite the flame then reduce the flame to between low and medium.  If the igniter continues to click, you most likely have a contact switch issue related to the problem burner.  
Unplug the cook top and turn off the gas.  After the gas is turned off, disconnect the gas line.  
Remove the cook top.  

Unscrew and Remove ALL of the burner bases by lifting them up.  The ceramic igniters may be difficult to remove but they will come loose if worked out slowly.  
Pull of the wire connected to the igniter. 
Remove to cook top top plate from the base, exposing the internal gas valves and wiring.
All of the burners are wired in parallel.   Lift off and unsnap the casing of the problem igniter switch.  The repair may require something as simple as, 1- cleaning the contact strips, or 2- slightly bending the non stationary contact strip to keep it from coming in contact with the stationary contact when in the off position, or 3- replacing the switch. 
Unless you comfortable and understand how electric systems and switches work, this is a job for a qualified repair person. 

Apr 02, 2009 | GE Cooktops

1 Answer

SGM464EM cook top valve rplacement


you have to go in from the top ,,, take off burner, knobs and the screws holding top and raise to get to valves / larry

Dec 11, 2008 | Dacor Preference SGM466 Gas Cooktop

2 Answers

Ignition does work - stove top doesn't light


Please provide model number so that I can tell you what to do for this unit.

Oct 29, 2008 | Thermador Cooktops

1 Answer

Jenn Air gas cooktop


pop me an email at b4829@yahoo.com and reference your cook top you can rate me later

Mar 29, 2008 | Cooktops

Not finding what you are looking for?
Cooktops Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dacor Cooktops Experts

Brad Brown

Level 3 Expert

16973 Answers

jdthefixer

Level 3 Expert

744 Answers

Mike
Mike

Level 2 Expert

166 Answers

Are you a Dacor Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...