Question about DLS A1 Car Audio Amplifier

1 Answer

Need help I have 2 Amp DLS A2..for my front system speaker Using DLS UR63s....can i use them...? can you show me? how to get dla A2 to work on 2ohm so power 2X145 watt? is sound different with 2ohm than 4ohm?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hi i would only use 1 of then in the bote then just plug the speeker whire in to it

Posted on Dec 27, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

If i hook up for 2 ohm do i use one speaker wire off amp bridged

Just use both speaker outputs, no need to bridge them,

Jan 25, 2012 | Hifonics BRZ17001D Car Amp

2 Answers

I got two DUAL 2omn speakers and i just need to know best way to wire them for a mono block amp. i have them wired parrallel in the box

With 2 speakers wired in parallel, the impedance will be halved, so you are presenting a 1 ohm load to your amp.
Many amps can drive a 1 ohm load, but not all of them. Check the specs for your amp.

If it can't drive a 1 ohm, then you'll need to rewire them in series. 2 speakers wired in series will double the impedance, so you'll present a 4 ohm load when they're wired that way.

Jan 29, 2010 | Kicker (2) S12L7 12in Solo-Baric L7 + (1)...

1 Answer

I want to know the best subwoofer wiring diagram for three kicker cvr 10 inch subs, 2 of them are dvc 4 ohm and 1 is dvc 2 ohm, the amp that i am using is jl audio 500.1 1.5-4ohms stable. can anyone help...

if the amp has a 2 outputs then i would wire the two 4ohms together, and the 2ohm by itself. and if its a 4 channel output then wire them all sepretly, if its a 1 channel output then wire the two 4ohms together and leave the 2ohm sub out

Nov 29, 2009 | Kicker CVR10 Car Subwoofer

1 Answer

I am trying to install my xtant 604x after i just had it sent out and repaired. I have 4 rca's coming from the head unit wired to the amp as FL, FR,RR,RL. The front speakers connected to the front output...

CLICK HERE for your Owners manual in PDF format
CLICK HERE for your Installation Guide in PDF format

As we agreed in chat - you are going to run your 4 channel amplifier as follows...

Front Channels of amplifier will run left and right independently.
Wire up the left speakers in parallel all + together and all - together.
This will yield a 2 Ohm load.

To the Same with the Right Side speakers - on the FRONT Right channel of the amplifier.

Now you have a 2ohm stereo load on the FRONT channels of your amplifier.

And using the BRIDGED nomenclature on the REAR channels of your amplifier - wire up your 4ohm sub mono.

Here is a crude drawing for a visual


Thanks for using FixYa - a 4 THUMB rating is appreciated.

Sep 05, 2009 | Car Audio & Video

1 Answer

I need to know how to wire a single 2 ohm sub to a concept cc-d800 to make amp run 2ohm

If your sub is 2ohm it's just left positive and right negative at the amp to the speaker. Hope this helps

Jun 26, 2009 | Car Audio & Video

1 Answer


Hello i_starling,

The Kicker L7's come in either 2ohm or 4ohm dual voice coil (DVC) versions.

Whatever amp they are connected to, you need to know both the impedance of your L7's and the impedance of your amp. The L7's dual voice coils can be wired to provide a total of four different loads:

2ohm coils in parallel = 1ohm load
2ohm coils in series = 4ohm load
4ohm coils in parallel = 2ohm load
4ohm coils in series = 8ohm load

Your best connection would be the one that results in a final impedance load that is supported by the amp.

Hope this helps.

May 01, 2009 | Car Audio & Video

3 Answers

I have 2 kicker l7 12 dual voice coil subs.. i just friend a hifonics 1600w amp and am wondering if a kx 1200.1 kicker amp will be enough to power them they are 750w rms a piece .. can these be run at 1...

it all depends on the impendance of your subs if u have duel 4ohm or duel 2ohm, 2 duel 4ohm speakers can be wired at 1ohm to the amp, and with a kx1200.1 that would be pushin 2400 peak and 1200rms
if ya have 2 duel 2ohm speaker than you can only wire them to 2ohm and would be pushing 1200 peak and 600 rms with the kx1200, so if you have the duel 4ohm i would go with the kx1200.1 and if u have the duel 2ohm i would go with the hifoncs

Apr 23, 2009 | Kicker KX1200.1 Car Audio Amplifier

1 Answer

How many speakers can I use?

This should work if channel 3 & 4 are bridged at 4 ohm.
channel 1 should be stable at 2ohm
channel 2 should be stable at 2 ohm
You can hook up the right side speakers together ( + with + and - with - ) . same thing with the left side. this will give you 2 ohm each channel. this will cause your amp to run hot (this might be tuff on the amp). It will give you right (2 speakers) and left ( 2 speakers ), no front and rear adjustement if you need to balance your sound. I think you should be better buying another amp for your sub and take your 4 channels for your 4 car speakers. this amp as a rca output that can feed the other amp ( sub amp ). it is possible to do it.

Good luck

Nov 11, 2008 | Alpine MRP-F250 Car Audio Amplifier

1 Answer

How can i get a 2ohm load outta 2 4ohm dvc subs can you show me how to wire the amp as well it says on the amp its 2ohm stable

A normal wiring setup to produce a 4-ohm load is what you usually see - each speaker is wired to one channel of the amp. This is series wiring. To get a 2-ohm load, you need to wire in parallel. Here's how:

Take sub A and wire the positive terminal to the positive terminal of channel 1 on the amp. Wire the negative terminal of sub A to the negative terminal of channel 2 on the amp. For sub B, it's the opposite - positive terminal of sub B to the positive terminal of channel 2, and the negative to the negative terminal of channel 1. That's parallel wiring, and will produce the 2-ohm loading (and subsequent increase in output) that you're seeking.

Aug 28, 2008 | Jl Audio Car Audio & Video

3 Answers

Yamaha dsp a2

Check the A or B switches it could be they are turned off!

Sep 28, 2006 | Yamaha DSP-A2 Receiver

Not finding what you are looking for?
DLS A1 Car Audio Amplifier Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top DLS Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4905 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

77932 Answers

Are you a DLS Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides