Question about Garmin GPSMAP 60CS GPS Receiver

1 Answer

It has just been refurbished!!!!! Now when I try to turn it on the screen flickers once every second!!!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 121 Answers

Get it straight back to Garmin. Personally I would look for a replacement as most Garmin software returns we get back in the shop end up being returned time and again until the customers get fed up and demand a new one..

Posted on Oct 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Plasma tv video


Could be the power supply inside the TV is bad. Check with your local authorized Samsung repair center. DON'T try to fix it yourself.

Dec 03, 2013 | PN50C675 Samsung Factory Refurbished...

Tip

How to reset the machine


Reset Procedure for Equator / Hirundo ( EZ3612CEE / EZ2512CEE / EZ1612V )
If the door of the machine is opening you can follow the below reset procedure so that the machine will function properly but if the door in your machine is not opening you need to first get the door to open by following the procedure as stated in the link http://www.fixya.com/support/r4240518-door_not_opening_in_equator_hirundo
Resting the unit will make sure that all the memory storage in the chip will be erased and hence the unit will be ready for a new cycle.
Reset Procedure
  1. Make sure that the machine is turned OFF.
  2. Make sure that the door is opening.
  3. Set the dryer & wash temperature knobs to the off position (12 o'clock / pointing vertically upwards)
  4. Make sure that the door is latched properly.
  5. Set the washer knob on the Red Reset position and switch on the power.
  6. You will observe that the mode + Door Lock light flickers rapidly for a few seconds and then flickers slowly.
  7. Once the light starts flickering slowly turn off the power.
  8. Set the washer knob to the Green Reset Position and switch on the power.
  9. You will observe that the mode + Door Lock light flickers rapidly for a few seconds and then flickers slowly.
  10. Once the light starts flickering slowly turn off the power.
  11. Set the washer knob to the Grey Reset Position and switch on the power.
  12. You will observe that the mode + Door Lock light flickers rapidly for a few seconds and then flickers slowly.
  13. Once the light starts flickering slowly turn off the power.
  14. Set the washer knob to the Reset Position on Delay Time and switch on the power.
  15. You will observe that the mode + Door Lock light flickers rapidly for a few seconds and then flickers slowly.
  16. Once the light starts flickering slowly turn off the power.
You have now reseted the unit and the unit should work fine now , in case you observe that the washer knob/Dial is going round and round all by itself now please go through the link for fault codes for further diagnosis.
Hope this procedure helps.

on Mar 02, 2010 | Washing Machines

2 Answers

RCA 37" FLAT SCREEN NON STOP FLICKERING/FLASHING SCREEN


you need to remove main ckt, (m.board) some part need to re solder specially in hot area. (lost contact i one of the flickering problem you encountered.

Mar 26, 2010 | RCA L37WD12 37 in. LCD HDTV

1 Answer

Bottom screen on ds lite flickers


check the cable first it might not be in the ribbon connecter properly, if everything looks ok chances are youll need to replace the screen.

Jan 17, 2010 | Nintendo DS Lite Console

1 Answer

My nintendo ds lite was dropped and now the top screen flickers once and then turns it self off and the bottom screen dosnt seem to do anything only the top screem flickers once which tackes about a second...


your fuse or fuses are dead. however, it is fixable, but it is extremely difficult.

1. if you don't have the time or the means or the wants to solder it, then sell it on ebay and you can get a fairly good price and someone else will fix it

2. if you do want to go through with this then you will need a meter, a soldering iron, and a lot of time and patience.

If you are interested, just notify me

May 09, 2009 | Nintendo DS Lite Console

1 Answer

Motorolla razr, black oldest edition


try another battery and if the lights just blink briefly....your main-board sounds like it is damaged so you may need a new one.

Jun 11, 2008 | Motorola Mobility RAZR V3

Not finding what you are looking for?
Garmin GPSMAP 60CS GPS Receiver Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garmin GPS Experts

SHARCNET-USA
SHARCNET-USA

Level 3 Expert

2130 Answers

yadayada
yadayada

Level 3 Expert

75066 Answers

TO Lady

Level 3 Expert

638 Answers

Are you a Garmin GPS Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...