Question about InFocus Proxima UltraLight S520 Multimedia Projector

1 Answer

I Followed the directions and changed the bulb. When

I Followed the directions and changed the bulb. When I started the unit back up there is now a spot with a blue tint in the top middle of the picture. Any idea of what the cause is?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,236 Answers

There is a burn spot on one of the light filters located next to the blue lcd panel. it is caused from excessive heat and dust. unfortunately, you'd need to replace the entire optical engine because infocus does not sell individual optical engine parts.

Posted on Oct 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I can't figure out how to remove the light bulb cover to change the light bulb. Followed directions in manual, but it won't budge. I fear breaking it--it takes only light pressure supposedly!


Some of the covers are molded plastic, give them a squeeze and they should release from one side. Some have metal latches on a glass panel to flip out of the way before you can slide them one direction or the other... but the manual is correct, it shouldn't take much force.

Apr 23, 2016 | Viking Refrigerators

1 Answer

JUST BOUGHT A NEW CRAFTSMAN WEED EATER ,FOLLOWED ALL DIRECTIONS AND UNIT WILL NOT START. Won't even fire once


If you have followed all the instructions then bring it back to the store and replace.

Apr 24, 2015 | Craftsman Garden

1 Answer

Trimmer starts easy and runs/cuts good from cold after about ten minutes or so it starts to lose power and run rough weaker and weaker until it dies


these little engines wear out so quickly and repairing them is not an option anymore.. I would buy a new unit for next year..

Jan 28, 2014 | Stihl Garden

1 Answer

How do i change a headlight bulb on a 2007 520d estate?


first is the headlight Xenon or normal? Xenon : The bulb is situated behind the backing cover on the light and is a clip on cover! remove this cover and the xenon bulb and module will be exposed. turn this unit anti-clock wise direction and it should come out easily. unplug the small wire and replace the bulb and or the small unit that has been removed. DON'T TOUCH THE BULB ! as this will damage it!
Normal: Remove the round cover and the bulb will be exposed !, remove wire connector and un clip the retainer spring, replace bulb!

Feb 08, 2011 | 2007 BMW 530xi Sports Wagon

1 Answer

How do i change headlamp bulbs


Changing the headlight bulb is a little bitdifficult for those not familiar with the vehicle. Both the high and low beamsare encased in a sealed unit, which also contains the turn signal, parkinglights, and side reflector. To change a single headlight, the entire headlightcompartment must be removed from the car. Once you understand how to remove thesealed headlight unit from the car, replacing the bulb is relatively simple.Follow the steps below on how to change the headlamp bulb in this car. Removal 1. Open the hood of the Jeep and locate thelong, headlamp jackscrew. The screw is located almost directly above theheadlight unit and can be removed using a 7-mm socket wrench. This will allowyou to remove the bezel from the grill opening panel. Remove the three screwsattached to the retaining ring to the headlight console. The screws are locatedon the bottom front and side of the unit. In some models the screws have beenreplaced with ball-stud alignment posts, enabling you to remove the headlightunit by simply wiggling it loose. 3. Disconnect the headlamp bulb wireharness connector located at the front of the headlight unit. This is locateddirectly above and between the parking and turning bulbs. 4. Separate the sealed headlight unit fromthe vehicle; disconnect and replace the old bulb. The high beam is locatedtoward the center of the car. The low beam is the bulb on the outermost edge ofthe unit. This is how to Install 1. Reconnect the headlamp bulb's wireharness-connector. Then Replace the headlight unit in the headlight canister. Positionthe retaining ring back in its original position and install the three screwsagain. If you wiggled the unit out, ensure that it is replaced firmly. 2. Install the headlamp bezel by replacingthe 7-mm jackscrew on the inside of the hood. Make sure all connections aretight before starting the car and inspecting the replacement.

Jan 14, 2011 | 2000 Jeep Grand Cherokee

1 Answer

How to change light bulb


If it is plastic vent cover there should be 2 screws apporx. 4 inches from each end,remove them tip top out and lift out.

Apr 22, 2009 | Microwave Ovens

1 Answer

I BOUGHT TWO DIFFERENT PROGRAMMABLE THERMOSTATS TO INSTALL IN MY HEAT PUMP SYSTEM, I FOLLOWED THE DIRECTIONS TO A T BUT WHEN I SET IT TO COOL THE UNIT REVERSES AND PRODUCES HEAT WITH BOTH THERMOSTATS. MY...


heat pumps normally have what is called a jumper wire between you R and RC, RC run cooling. You may not have the jumper installed correctly. Instead of RC you may be using RH run heat

Aug 09, 2008 | Heating & Cooling

1 Answer

GPS - TOMTOM ONE XL - first time locating position via satellite


The unit was fully charged from the factory. Turned on thwe unit and followed simple directions to position my location. Rest followed.

Mar 30, 2008 | Tomtom GPS

Not finding what you are looking for?
InFocus Proxima UltraLight S520 Multimedia Projector Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top InFocus Office Equipment & Supplies Experts

Juan Carlos Pacheco

Level 1 Expert

36 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

The Knight
The Knight

Level 3 Expert

73619 Answers

Are you an InFocus Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...