Question about Philips 55PP9401 55" Rear Projection Television

Open Question

My philips 60PP9202 converge multipoint lines will NOT line up when i try to adjust them!! please help!!!

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Slinteriors
  • 8617 Answers

SOURCE: convergence problem on a Philips projection TV

They should be STK392-120 but check the numbers on yours to be positive. They are located on the extreme left of the chassis looking inside the back panel mounted on a heat sink. They will have STK Numbers stamped on them. Yes you should change both of them they cost 10.00 each at electronix.com You will need heat sink compound as well but this is better purchased at Radio Shack 2.00 per tube. Put a good coat of Heat sink compound on the back side of the new ICs. Also check over the resistors on the board next to the ICs sometimes 1 or 2 of those burn when the Cs go out. Let me know if you need anything further

Posted on Jan 25, 2008

  • 979 Answers

SOURCE: Phillips rear projection tv model #60pp9202/17f

Convergence problems! If the mechanical set-up and electronic adjusts aren't cutting it, you may very well have to replace one or more devices on the red conv board, including but not limited to, the conv IC....accordianman

Posted on Feb 25, 2008

  • 38 Answers

SOURCE: 60pp9202/17f Cant adjust Red Horizontal convergence

chang the convergence ics

Posted on Oct 13, 2008

SD Tech
  • 14553 Answers

SOURCE: My Philips 60PP9202 has blue wavy lines that comes

Go into the customer menu with the remote and look for "convergence" if the red or blue will not adjust in some direction you have a bad convergence chip. This set uses 2 STK-392-120 chips---both need to be replaced along with any of the 6.8 ohm resistors around them that are bad--a bad resistor will be discolored or white in the middle.

With the back cover off the chips are located on two metal heat sinks on the large board on the left side (as you look from the back) and both will have the STK-392-120 number printed on them in white--the chips are black in color.

Most of the time you just need to replace both chips and adjust the set with the remote control. You can buy both chips for about 13 dollars on Ebay--if you can do this repair yourself you will save a lot of money!

Most shops charge 300-400 for this kind of repair---I do lots of them here for 200-250 including parts, labor and house call. Now is the slow time of year for TV repair shops--shop around--if they say "it has to go to shop" keep looking; any good tech can do this repair in your home and it usually takes about an hour.

I do not know how much skill you have but if you need instructions I will help you. This problem happens for a simple reason--the chips are about 2 inches wide and 1 1/2 inches tall with 18 pins each--the back of each is metal and a white grease is applied to each to transfer heat quickly to the metal that they are bolted to. After some years the grease dries out from the heat and one of the chips cannot move the heat fast enough and it fails.

IF YOU HAVE ANY QUESTIONS OR NEED HELP CONTACT ME BY REPLYING TO THIS POST.

I DO THIS here for free so if this has helped you take a minute and give me a vote here.

SD TECH

Posted on Sep 04, 2009

  • 8457 Answers

SOURCE: Our phillips 60" TV

Ur convergence is dead.Know how to solders?Must changed the 2 convergence ICS,and all it resistors.Tries Tv repair World.com,Tvrepairkits.com for the convergencce kit.The shop will cost $300 for parts and labors.

Posted on Feb 01, 2010

Testimonial: "Thank you for the great advice!!!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Our phillips 60" TV


Ur convergence is dead.Know how to solders?Must changed the 2 convergence ICS,and all it resistors.Tries Tv repair World.com,Tvrepairkits.com for the convergencce kit.The shop will cost $300 for parts and labors.

Feb 01, 2010 | Philips 60PP9202 60" Rear Projection...

3 Answers

Philips 60pp92902/17f television convergence issue


actually your vertical display ic is faulty....you need to replace them

Jun 20, 2008 | Philips 60PP9202 60" Rear Projection...

2 Answers

Multipoint blue convergence cannot be adjusted


Sound like you need to replace the STK's and any blown pico's on convergence board.

Jan 20, 2008 | Philips 60PP9202 60" Rear Projection...

2 Answers

I have a Philips 46PP9302 and can't find the Quick Setup guide. I'm wondering if it is located on-line. We moved our tv and want to recalibrate it.


http://www.retrevo.com/support/Philips-46PP9302H-TVs-manual/id/278ci462/t/2/

The above link should take you to the location where you can view all the parts of your models manual. Select the area of interest and rad onlinje


Please rate my help++++Thanks for using FIXYA

Nov 24, 2009 | Philips 46PP9302 46" Rear Projection...

2 Answers

Getting lines to line up


Hi, if the green isn't straight to begin with you will need to go into the convergence sub menu and align it there code is 062597 status then follow the instructions to adjust the green first, then red , then blue multipoint and save it.
pressing menu to switch arrows to move/adjust status to back up , make sure to scroll down to save multipoint before exiting, power off when done.
If any color will not move or is more than 1 inch out of adjustment you may need to check the resistors to that convergence color .
hope this helps
Eric

Aug 23, 2009 | Philips 55PP9401 55" Rear Projection...

1 Answer

My Philips HDTV 60PP9202 has blue and red curved lines



Check to see if you can adjust the convergence. If you can't adjust the red and blue in all directions you need to replace the convergence chips and resistors. If you not sure how to check the convergence goto the site www.TvRepairKits.com and goto the Tips section. 

Dec 25, 2008 | Philips 60PP9202 60" Rear Projection...

5 Answers

Phillips rear projection tv model #60pp9202/17f


Here are some of the most common symptoms and example photos of a convergence problem

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
701cb04.jpg
77ea520.jpg
f0900cb.jpg
Here is a quick test....

Using your original remote go-to the tv settings then goto the convergence section.

Try to adjust the red and then the blue convergence.



You should be able to move them up, down, left, and right.

If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem.

2c07611.pngSolution #1

You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick note and they will put one together for you. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, etc.

Feb 25, 2008 | Philips 60PP9202 60" Rear Projection...

1 Answer

Picture Quality


Sounds like your convergence amps are probably bad. Check out http://i114.photobucket.com/albums/n248/OFilippov/Dont%20look/Pioneer/BadPicture03.jpg and see if you have similar bowing between red and green when you try multipoint convergence. If so, you'll need new convergence amps, part STK392-120. Most people who are handy with a soldering iron can replace these parts in a couple hours.

Jan 15, 2008 | Philips 60PP9202 60" Rear Projection...

1 Answer

Philips 60PP9202 60 in.


sound like your convergence amps are blown. also known as stk's

Dec 19, 2007 | Philips 60PP9202 60" Rear Projection...

1 Answer

PHILIPS 50P8341 60 IN.


Check the other posts for convergence problems. This may be what you're experiencing. Have you tried bringing it in with multipoint convergence? It's under Menu -> Picture -> Manual Converge -> Multipoint Red and Multipoint Blue.

Dec 07, 2007 | Philips 60PP9202 60" Rear Projection...

Not finding what you are looking for?
Philips 55PP9401 55" Rear Projection Television Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

73635 Answers

matt martin
matt martin

Level 3 Expert

1208 Answers

Jaime Hernandez

Level 3 Expert

2315 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...