Question about Saws

1 Answer

I need spare parts for my saw and if possible a diagram parts requierd are carbon brushes x2 and brush holder assembly . Kind Regards Stephen.

Posted by on

  • 1 more comment 
  • Johnny
    Johnny May 11, 2010

    model number?

  • Johnny
    Johnny May 11, 2010

    model number?

  • David Ford
    David Ford May 11, 2010

    what is the brand and model number and I will try and find you one. Usually the brushes are each, but depends on the MFR. Let me know

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mastercraft 10" compound saw model #55-6802-6-- need spare parts - How do i get them.
Need center bolt for blade

Posted on Dec 05, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace brushes when they will not come out normally?


I had the same issue. Turns out the brushes were fused into the brush mounts. I pulled on the copper end cap and wire only to break it off at the carbon brush end. I had to pull the motor out of the housing (stator) to expose the brushes. I then used a tool to push the carbon brushes back in and out of the brush mount assembly. You could also push from the outside in, just make sure you get all the carbon pieces and use a tool that won't put scratches in your brush housings. My brushes where well over 1/2 inch long....but they were just fused into the assembly, so the spring wasn't pushing it properly against the commutator, which I am guessing was the reason my saw just stopped in mid use....I had ripped a straight line in a board and stopped for a few seconds to reposition the saw only to find it no longer worked.

Apr 28, 2014 | Makita 7 1/4" Circular Saw 5007NB

1 Answer

How to remove carbon brush holder from my skilsaw 77


make sure saw is unplugged.. remove brush caps on both sides of saw to remove brushes...

May 26, 2012 | Skil Saws

1 Answer

Carbon brush has broken and is stuck in so i cannot put a new one in, on Einhell sliding mitre saw


If you cannot get the carbon pieces and/or spring out of the brush holder your only option is to take the saw apart and remove the armature. From there you can either push the carbon piece(s) through or out from the other side. It will also give you a better assessment of any damage caused to the brush holder and armature contacts.

Feb 22, 2012 | Saws

2 Answers

I have a makita 2703 table saw. Saw would not turn on from time tio time, then just would not turn on at all. Just replaced the switch and verified no other wiring issues up to the motor.


First thing I would check are the Carbon Brushes. The are # 75 in the picture

dennis675_7.gif

Hope this answers all your questions
Please remember to Rate/vote for any solution that helps you out.
Thanks for using Fixya.

Jul 01, 2011 | Makita Saws

1 Answer

Flexible Shaft Adaptor # 2221-MA00009-00 Carbon Brush # 03AT-000046-00 Brush Spring # 02AH-000088-00 For a Mastercraft Maximum Spin Saw Kit Model # 54-8205-8 Cdn Tire...


By robert_lessa on May 09, 2011
Flexible Shaft Adaptor # 2221-MA00009-00
Carbon Brush # 03AT-000046-00
Brush Spring # 02AH-000088-00

For a Mastercraft Maximum Spin Saw Kit
Model # 54-8205-8
Cdn Tire doesn't support their own "house" brand with spare parts.
Does anyone know who was contracted by Cdn Tire to make this unit? That could give me an alternate source for spares. Any help would be much appreciated.
Thanks, Bob
------------------------------------------------------------------ Canadian Tire stopped supporting this product in 2008 and have no parts in inventory ( I am not convinced they ever had a stock of parts) The Spin Saw was manufactured in China by Choon Nang Electric. Your best bet is going to a small engine repair shop and ask if they have universal parts which could fit. Best of luck Claude

May 09, 2011 | Garden

2 Answers

I have a aeg ph38 electric 800 watt chipper hammer, i need to find carbon brushes and the carbon brush holders for the tool.


RE AEG PH 38 Brushes go to local hardware storeinthe miscelleanous everything aisle and look or a SKIL brush set exact size match $4.50 US cost I fixed mine today. Brush holders another issue

Apr 25, 2011 | Garden

2 Answers

Where can I get brushes and at what cost?


Parts for Remington saws are few and far between. Brushes are a common failure point and those available have about been bought up. You best chance is to check with a well-stocked hardware store or an electric tool repair shop for a similar brush from a different tool. You may have to modify something similar to fit. Good luck!

Dec 11, 2010 | Remington 111409 - 01 6" Branch Wizard...

2 Answers

Am I wise to purchase a Remington Pole Saw or should look for another manufacturer? Which Remington Pole Saw would you purchase: a. 18V Cordless b. 10" Electric


Remington Saws have ceased operations and, unless you like to make your own replacement parts, they are prone to failure. The gearbox is sealed and the motor brushes are not available anywhere. Look elsewhere!

May 11, 2010 | Remington Electric Pole Saw

1 Answer

Bosch wfr2460


hi Many universal motor malfunctions are caused by wearing down of the carbon brushes, the soft blocks of carbon that complete the electrical contact to the motor's commutator. When these brushes become worn, the motor will spark, and electrical contact may be incomplete.try this
Step 1: To sight-check the carbon brushes, remove the screws that hold the brushes and brush springs into the brush holders at the sides of the commutator. The screws will pop out of the screw holes; turn the motor over to tap out the brushes. The ends of the brushes should be curved to fit the commutator; if they're worn down, new brushes are needed.
Step 2: To check carbon brushes with a continuity tester, remove the motor lead wires from the circuit. Tag the wires as you disconnect them so that you'll be able to reconnect them properly. Hook the tester clip to one motor lead and touch the probe to the other lead; the tester should light or buzz. Slowly rotate the motor shaft, keeping the tester in position. If the tester doesn't light or buzz, or if it flickers or stutters when you turn the motor shaft, the brushes should be replaced. If the springs behind the brushes are damaged, they should be replaced as well.

Step 3: Replace worn carbon brushes and damaged springs with new ones made specifically for the motor. The model information (number and make) is stamped on a metal plate fastened to the motor, or embossed on the metal housing of the motor. If you can't find the model information, take the worn brushes and springs with you to an appliance-parts store to make sure you get the right kind. Insert the new springs and brushes in the brush holders, replace the brush assemblies, and secure the new brushes with the mounting screws that held the old brushes.

Sep 13, 2008 | Bosch Axxis+ WFR 2460 Front Load Washer

Not finding what you are looking for?
Saws Logo

Related Topics:

530 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saws Experts

Tom Chichester

Level 3 Expert

34255 Answers

ray gallant

Level 3 Expert

43174 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1793 Answers

Are you a Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...