Question about Mitsubishi WD-52725 52". Rear Projection HDTV

1 Answer

TV OUT My TV goes out and then the power light starts blinking. I read yuo have to hit the reset button and then let it blink and it will stop after a minute or so. Then yuo are to turn the power on. My wife tried this and it did not work. Please help. It's a mitsubishi HDTV 46 in

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Take your bulb assembly out and take it a TV repair shop and have them test it if you can't see that it is bad. if it is bad go to website and you can buy just the bulb for less than $130.00 including S&H. It was easy to replace.

Posted on Dec 29, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Red light blinks six times. When I hit power button green light stays on for a few seconds, turns off the on for a few more. Then goes back to pattern of red light blinking six times.

the kill switch is open ensure the lamp cover presses firmly on the kill switch when u close the lamp chamber door the red light will stop blinking and u can now turn the tv on

Jul 06, 2013 | Projection Televisions

2 Answers

Power will not come on even after system reset. Pushed reset and LED flashes then after it stops flashing TV will still not turn on.

do self check: when it shuts off and power light goes off:

On front of set press and hold both menu and input (device) buttons for at least five seconds and release both buttons.

Power light will blink a two digit error code, like 2 blinks, 2 blinks, a pause and repeat it several times.

Let me know what error code and I will assist you


Sep 24, 2010 | Mitsubishi WS-55513 55" Rear Projection...

2 Answers

Tv will not turn on,just has the flashing green light.after reseting the tv via the reset button the same problem persits

try hitting the sleep button over and over it reset my timer and I have had no more blinking green light problems

Nov 15, 2009 | Mitsubishi WD-62725 62" Rear Projection...

2 Answers

Standby light keeps blinking. tv wont turn on

If the TV goes off completely, then is usually a faulty power board.

If the TV goes in standby, then it is in protection mode.

Ensure also that the fault is not coming from a faulty receiver box sending
bad signal, check if you get same problem on DVD with no receiver box

Try first leaving the TV power cord unplugged for some times, let say one hour or so.

The flashing light indicates a diagnostic state called protection.
When the TV goes on protection there are only two possible causes.

1The internal circuits are jammed because of electrostatic charges accumulating on capacitors, or because of a wrong voltage read by the main chip on your monitor controller board. this started the protection circuit.

2 The protection circuit detected a wrong voltage or abroken contact, identified an internal fault and kicked in , starting the flashing light.

If you are in situation one, then the TV will reset just unplugging power cord for one or two hours,sometimes even minutes.

If you are in situation 2 , then there is an internal fault.

If under warranty contact the manufacturer ringing the number on the user manual

If you want to repair at your own expenses, just locate any good qualified repairer.

If you want to DIY you find parts here,

All: Appliance parts, electronics parts & more from

Encompass Parts Distribution

LCD/Plasma Electronic Replacement Parts: Plasma & LCD TVs, Appliances |
On Rear Projection : check lamp, lamp ballast, power board, and convergence.

May 07, 2009 | Projection Televisions

3 Answers

Green light blinking

The green light on the front blinkes and does not stop even after hitting re-set button.

Oct 26, 2008 | Mitsubishi WS-65513 65" Rear Projection...

2 Answers

I have a 62 inch mitsubishi dlp model#wd-62525 serial#125902 , tv will not power up it has a flashing green lite below the timer button that flashes,i have try the reset button but it just starts blinking...

if the light just constantly blicks green and doesnt stop. You will need the" V26 DM repair kit " which will usually repair that issue. You can get the repair kit at the following link which includes the replacement capacitor and instructions

Sep 26, 2008 | Mitsubishi WD-62525 62" Rear Projection...

1 Answer

Timer light blinks on and off and tv wont turn on

Resetting the TV
If the buttons on the remote AND the buttons on the TV case do not work (channels do not change and you cannot open or navigate the menu), the TV has stopped responding. Reset the TV as follows:

Some TVs have a reset button. If available and accessible, try using the reset buttons before using the steps below. Using the reset buttons can save time.
1. Unplug the TV power cord from the power outlet.
2. Unplug any connected devices (DVD, Set-top boxes, etc...)
3. Press and hold the TV power button for five seconds.
4. Plug the TV power cord back into the power outlet and turn on the TV.
5. Open the on-screen menu to confirm that the TV is responding again.
6. Turn off the TV and reconnect the devices.
7. Turn on the TV.
If ever resetting is no effect then the problem is in the "DM board"
The constant blinking green light means that the TV is not booting up. This is a common problem on this set. Hope it may help you; Regards, VOTIT

Sep 25, 2008 | Mitsubishi WS-55809 55" Rear Projection...

3 Answers

Where can I find a Samsung repair center?

LG DLP PROJECTION TV (RU-44SZ63D) Tv light is off (with red light on). When I hit the power on button the red tv light starts blinking. Light continues to blink red then stops blinking and goes back to off (red light on).

Jul 12, 2008 | Projection Televisions

1 Answer

Blue screen and shut off by self

You will need to reset the Netcommand and tuner settings in the set. The little indented button in the front of the set needs to be pushed in (when the set is off). The front light will blink for about a minute or minute and a half. Then, reprogram the Netcommand settings. This should solve your problem. If you need more information, then, reply to this post and I will respond.

Sep 23, 2007 | Mitsubishi WD-62525 62" Rear Projection...

Not finding what you are looking for?
Mitsubishi WD-52725 52". Rear Projection HDTV Logo

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Projection Televisions Experts

matt martin
matt martin

Level 3 Expert

1187 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

The Knight
The Knight

Level 3 Expert

66330 Answers

Are you a Mitsubishi Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides