Question about Network & Wireless Adapters

1 Answer

Dynamo R-ADSL-C4W-EG WAN light

Hi. My problem is the wan light on my modem. When i first start the modem the wan light flashes about 10 or 20 times then goes off (which meens no internet connection) It is setup properly with the filter supplied but still no cnnection. the wireless and LAN Work for getting into the router but still no internet connection. Any Help would be appreciated. Please email to

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert who has written 20 answers of more than 400 characters.


    An expert who has answered 20 questions.

  • Contributor
  • 79 Answers
Re: Dynamo R-ADSL-C4W-EG WAN light

Have you conifgured it with the proper credentials? PPPoE or PPPoA? (since using a filter normally indicates a DSL connection)

Posted on Dec 23, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

INET light is on not able to connect to internet

Checked the instruction manual online. There's no INET light indicated. There's Power, Status, WAN, WLAN, and LAN LEDs. The WAN LED only indicates that the WAN port is connected to another device, e.g., cable or DSL modem. Check on your cable or DSL modem to see if the Internet light is on. If so, then you'll need to log into your router and go through the configuration/setup per the manual for your type of connection.

Oct 18, 2013 | D-Link 802.11g Wireless Router WBR-1310...

2 Answers

How to install d link 802.11G wireless access

Connect modem lan cable to Router Wan / Internet port. From Router Lan port you can either connect your system or switch . wireless : Scan for wireless network from your wireless system. If it shows, connect to your wifi network

Mar 25, 2011 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Hi, I am trying to install D-Link router WBR-1310 but getting the error code 101 IP address not maching. What do you suggest?

Use the PING command to test the communication between the computer and the gateway.

Goto Start > Run and enter COMMAND.
From the Command Prompt, enter PING
The gateway should reply.

Verify that the residential gateway is getting power. With the broadband modem connected to the WAN port on the gateway, you should have a soild WAN link light. You should use the same cable that connected the modem to the PC to connect the modem to the WAN port on the gateway. Any port on the gateway that has a computer connected to it should have the corresponding LAN link light lit. If you do not get the appropriate link lights, try using different cables.

onfigure browser/Internet Options
Step 1 Go to Start > Settings > Control Panel.

Step 2 Double-click the Internet Options icon.

Step 3 On the Security tab click Restore the default security level.

Step 4 Click the Connection tab and set the dial-up option to Never Dial a Connection.

Step 5 Click LAN Settings. Nothing should be checked. If anything is checked, uncheck it. Click OK.

Step 6 Click the Advanced tab and then click Restore these settings to their defaults.

Step 7 Click OK.

Step 1 Turn the Cable/DSL modem off.

Step 2 Turn the D-Link router off.

Step 3 Wait 60 seconds.

Step 4 Turn the cable/DSL modem back on and wait until all the lights are steady.

Step 5 Turn the D-Link router on.

Most routers and modems do not have an on/off switch. Simply unplug the power. Unplugging the power will not reset (reset back to default settings) the unit.

Nov 09, 2010 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Adsl wont stay on ,quick set up ,says cant find modem

Either the router is not connected properly to the modem, or the modem is not set up properly. First, unplug the router from the modem and disconnect power to both of them. Make sure the modem is connected to its data source, in this case the telephone line. Make sure the company has authorized the modem and make sure it's connected to the phone socket they specified, if they did. You should plug a CAT-5(ethernet) cable between the LAN port on the modem and the WAN port on the router. Now power on the modem. Wait until the modem's lights indicate it has a connection. If the modem doesn't indicate a connection, call your ISP. It will probably be as simple as them sending a refresh signal to it. After the modem finds a connection, power on the router. Your internet service should now be working. If not, try plugging the computer's network cable directly into the LAN port on the modem. If that computer then has internet, your problem is with the router. If the computer still doesn't have internet, then the problem is either with the settings on the computer or there's still a problem with the modem/ISP

Feb 27, 2010 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

When i am connecting my reliance net setter huwaei 3g modem it shows an error 678

hi alkam49...
This is most common problems. It is due to poor connectivity. Problem can be anywhere between B.RAS - Tier 2 - DSLAM - Modem - PC of the customer.
Switch off / Switch on Modem (Power Switch at the back of modem ) and wait for 2 minutes. Then retry.

If problem is not solved then Reset Modem [Back pin (in the hole) to be pressed in switched ON condition]
[Note : Link PC in black type Modem or WAN / LAN in white type Modem will go Off and then ON and system may be stable. Then retry.
If problem is still not solved then
a)Check link lamp in Black type Modem or WAN lamp in White Modem. If it is blinking, then it is line problem.
b)Check Modem to splitter connectivity.
i) Jack in & Jack out the cable of / to the modem and to the splitter
ii)Jack in & Jack out the telephone connection of the splitter.
If lamp is still blinking - then it is due to poor line condition / fault.
The case has to be referred to Area Broadband Team for attending the fault.
try this and get going...
post comment for any further assistance.

Dec 24, 2009 | Acer Network & Wireless Adapters

2 Answers

How do I hook up a Berklin wireless router to my comcast internet

Use an Ethernet cable to connect the port on the Comcast modem to the WAN port on the Berklin (Belkin????) router.
Use another Ethernet cable to connect one of the LAN ports on the router to the Ethernet port on your computer.
Start Internet Explorer on your computer.
Connect to the web-interface inside the router.
Run the "network setup wizard".
Run the "wireless setup wizard".

Nov 17, 2009 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Need to know how to hook up my router and where the cables go i have the basic idea but need help


1. connect the cable from the modem to WAN port 2. configure one IP for WAN port in the sebnet of modem (say 192.168.1.x) 3. Configur differnt subnet to the LAN (say 192.168.0.x), you can enable dhcp server router
This will help you more for any help. feel free to contact

Oct 17, 2009 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

I have a cable modem and wish to add Wireless. I have a Netgear 54 Mbps Wireless ADSL Firewall Router DG834GB v3 but not the instructions to install it. Not sure what goes into where from the original...

In general, the ethernet cable from your cable modem will plug into the WAN port on your wireless router. If you had a PC plugged into the cable modem, that PC will now plug into one of the other free ports on the wireless router.
You can get documentation and install guides from netgear's site. try this link:

Oct 04, 2009 | Network & Wireless Adapters

1 Answer

Can not connect to internet

My first guess is that your Dlink ADSL modem is really a modem router, so you are getting double routing. Sometimes this works just fine, though, so I'm not confident that's the whole explanation.
You'll need to setup your IP plan carefully
set the D-Link modem(router?) to bridging mode & the DLink wireless router does the login to Exetel.
DLink wireless router WAN side: DHCP + login to Exetel
DLink wireless router LAN side:
DHCP on: range to .20
DNS Servers:,
with PC's wireless adaptor set to DHCP
so picks up eg:
IP address:
Gateway address:
DNS Servers:,

Aug 03, 2009 | Network & Wireless Adapters

2 Answers

Hi I Have Problem

Hi Andy,

The WAN port on your Aztech DSL600EW (by default) is configured to be automatically assigned an IP address when connected to a cable modem (Motorola). Connect the WAN port of the Aztech DSL600EW to the Ethernet port of the Motorola, then configure the Aztech for wireless connectivity to your laptop as per the manual instructions.

Apr 18, 2008 | Network & Wireless Adapters

Not finding what you are looking for?
Network & Wireless Adapters Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Network & Wireless Adapters Experts


Level 3 Expert

18259 Answers

 C. Dante
C. Dante

Level 3 Expert

623 Answers


Level 3 Expert

2072 Answers

Are you a Network and Wireless Adapter Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides