Question about Konica Minolta DiMAGE Z1 Digital Camera

Open Question

Shutter screen on the back display has come un clipped at one side

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i get the wireless remote to work for my Nikon D3000?


Press the [info] button to bring up the information display. Press the [i] button to put the cursor into the information display. Use the cursor buttons to select the release mode (on the right side of the screen, fifth from the top). Quick-response remote mode (marked by a remote icon) fires the shutter when you press the button. Delayed remote mode (marked by a remote and "2s") gives you two seconds to hide the remote behind your back before firing the shutter.

This is all explained in the "Release Mode" section of the manual (page 53 in my copy).

Feb 01, 2011 | Nikon ML-L3 Remote Control

1 Answer

N70 BACK CAMRA NOT OPEN HOW CAT SOLV


Hi,

Back cover is obviously very easy. Front cover has 4 clips one each side at top and bottom, just need to gently pull the casing away from the body in each corner until the clips pop out. The piece over the camera at the back is a little more tricky, it's got two clips, one each side at the bottom, check your back shutter it connected with a camera switch. Remove the back of your phone & then set it again.

Nov 26, 2010 | Nokia N70 Cellular Phone

1 Answer

What tools do i need to change the headlight in a 2005 kia optima


No tools on the left side but on the other side with the battery.
You will need to take out the battery.
Just screw the cap off inside which is behind the headlight.

There is a clip in there.
Just un-clip it . It is a clip that attached underneath after when you take the clip off.
Remember how you un-clip it !!!
That way when you clip it back in , it will be alot EASIER !!!

Don't touch the tip of the headlight BULB.

Jan 29, 2010 | 2005 Kia Optima

1 Answer

How do you get the back off of an old Whirlpool washing machine? My washer won't spin so I think it needs a belt but I can't even look because I can't get the back off of the machine. I also can't find the...


The back does not come off. You lift the case off of these. The model number should be either on the back of control panel or lift the lid and look around the inside lip of the opening. To get inside the machine:
There is a screw on each end of the control panel. Pull the panel forward while lifting and it will pivot back out of the way. Then there is a clip on each back corner, un-clip them and unplug the wire in the middle. Grab the inside of the opening on each side and lift up and forward. This takes the case off. This machine has no belts. It's a direct drive, meaning it has a coupler. Look behind the motor and there will be a black rubber piece. This is part of the coupler. To get it off, un-clip the pump, take screws out of the clips on the motor. Then un-clip the motor. The piece attached to the motor is the coupling. There is another piece still attached to the transmission. Replace the coupler and it will fix the problem.
Please rate this solution

Sep 04, 2009 | Whirlpool Washing Machines

1 Answer

Water will not shut off when filling and how do i get front of the washer off


There is a clip located close to each corner of the top of the front panel. I use a putty knife, slip it into the gap between the top and front panel.Slide it toward the corner. It will stop when it hits the clip. (Around tow or three inches from corner. Now that you have located that one, pull putty knife and push it back in so that you pushing the clip back toward the machine console while you try to pull the front toward you. It will un clip. You might have to push hard or hit with your hand. Now you have that one un clipped, do the same to the other one on the other corner. If your not careful, the first one will re clip while trying to un clip the second. Now you have the front panel off. The problem with your machine is either a bad pressure switch or and tube running from it to the side of the tub has a hole in it, clogged or has come unplugged. Look for a clear vinyl tube running down the side of the tub. It will connect to a piece attached to the side of the tub. Check to see if it's still connected. If so pull it loose and blow through it. Checking for holes in it or clogs. If it's not clogged, or have holes or it's unplugged, you have a bad switch. I would say it's a 90% chance that it's the switch.
Please rate this solution if it was helpful. This makes it worth our time to answer these questions after working on these machines all day. Thanks

Sep 02, 2009 | Stainless GE® 3.5 Cu. Ft. Capacity...

1 Answer

I am taking apart my Kenmoore 80 Series washer due to the coupler needing to be replaced. Is there a quick tutorial on taking the motor off to get to the coupler?


its easy

1-remove the washer cabinet -- usually take screws off controll panel the flip it back, remover the 2 metal clips and un plug wire harness

2-take clips off pump - flip it to the side

3-take clips off motor - usually 2 screws there too. un hook wire harness and pull motor off

there is the coupling

Jan 24, 2009 | Washing Machines

1 Answer

Fujifilm F470: camera opens, shutter opens but no image!!!


I had the same problem with this particular camera. Here is the necessary steps to fix your problem.
1. Take out the battery because you dont want to short anything when you're inside it.
2. Free yourself of any static.
3. Remove six screws on the outside of the camera. Note that two of the screws in the botton are not phillips head. If you have a very small flat-head screw driver that will work.
4. Pull the camera apart very carefully. Unplug the little wiring harness by pulling up the little black clip that holds it in its seat.
5. Carefully remove the LCD screen. You dont have to remove any screws here. Just carefully pull it out. There is a peice of double sided tape that holds it in in place so you will fell some resistance.
6. Remove the two screws behind the screen that holds the lcd holder in place. Theres also one or two in the left side of that.
7. Plug back in the lens wiring harness. This is where your problem was. It came unplug from probably being dropped.
8. Repeat the steps 6,5,4,3,2, and 1 to put it back together.

Hope that this fixes your problem. It fixed my camera.

Dec 07, 2008 | Fuji FinePix F470 Digital Camera

1 Answer

I have a very nice 35 mm nokia camera with a zoom lens and lately when i get the pics developed, the pics come back blank or black. what could be the problem?


Black pictures mean under exposed or un- exposed film

Underexposed film can mean incorrectly set up or metering failure
Un exposed film simply means the shutter has failed
Open camera and look through the back and operated the shutter
Does it work?

Sep 02, 2008 | Cameras

2 Answers

My lcd screen is black


hi there guys, if the screen is black and the camera takes black pictures, then you should look if you are getting a on screen display on camera mode. if you are then i would say one of two things, either the shutter is not opening or the ccd( electronic imaging device) is not functioning. to check the shutter you should look into the lenses centre part and check for movement from the shutter to see if it is opening.

Jun 06, 2008 | Panasonic Lumix DMC-LZ2 Digital Camera

Not finding what you are looking for?
Konica Minolta DiMAGE Z1 Digital Camera Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Cameras Experts

kakima

Level 3 Expert

102366 Answers

Greg Cann
Greg Cann

Level 3 Expert

1114 Answers

Willem.
Willem.

Level 2 Expert

359 Answers

Are you a Konica Minolta Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...