My remote control stopped working and I have lost the booklet with the code. Please can you help I haven't had to get up to change a channel since I was a kid, it's not fun. The remote is a phillips universal, the tv is a sylvania. Thank you

I suggest you try these steps..

1.Turn the television set on by pressing the "Power" button on the set.

2. Find the "Code Search" button on the Philips Magnavox remote. This button will be labeled or will be a different color than the other buttons on the remote (depending on which Philips Magnavox remote you own)

3. Hold the "Code Search" button down for about ten straight seconds. The light on the Philips Magnavox remote should then stay on.

4. Starting pressing either the "Up" or "Down" channel button on the Philips Magnavox remote. Continue pressing the same button until the television responds to the remote. It could take a few minutes for the channel to change so you'll need to have patience when searching for the remote code in this manner.

5. Press the power button on the Philips Magnavox remote once the channel has changes. If the device shuts off, press the power button again to turn the TV back on. If the TV turns on, the remote has been programmed correctly. Repeat the entire process if your remote is not programmed.

I hope this helps...

Codes for BUSH

010 012 020 023 025 026 028 029 033 052 063 069 101 116 121 132 133 140 168 170 172 309 317 320 321 326 378 404 411

I can help you with your URC-3021 Universal Remote Control issues.

The codes for Sanyo TVs is: 0154.
The codes for RCA DVDs are: 0522, 0571, & 0717.
The codes for Magnavox DVDs are: 0503, & 0675. These may or may not work with newer Blu-Ray players. Since you have two disc players, you will need to reassign the CBL/SAT key to act as a second DVD key.
I don't believe the URC-3021 stores codes for surround sound amplifiers: it has only three function buttons: TV, DVD/VCR and CBL/SAT.

For complete instructions on entering the URC-3021 remote codes, please refer to my posted Fixya Tip One For All URC-3021 Code Entry.

I hope that helps.
_______________________________________________
Reassign URC-3021 Device Key
Urc-3021 Code List Download
One For All URC-3021 Code Search

you need to supply the SONY TV model just do a google of any URC booklet and then look uo the ctrl codes for your TV it has little to do with the brand of the remote

please rate our help to keep service online

link to codes is at bottom

Great News!! We can program most Philips Universal Remotes with Automatic Code Searh. Here's how it works on most of our remotes.

Programming with Code Search

1. Manually turn on the device (TV, VCR, etc.) to be controlled.

2. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.

3. Press and release the desired mode button (TV, VCR, etc.). The red indicator blink, then stays lit.

4. Press the Channel Up button repeatedly (up to 300 times) until the device could be controlled changes channel. The red indicator blinks, then stays lit. If you accidentally overshoot the code required, press the Channel Down button to backtrack through the library until the device changes channel. Pressing Channel Up changes direction to forward again. Press and release the Mute button to install the code.

The above assumes that you want to store the VCR you want under the VCR but, Cable codes under the CBL, etc

Note: if the device does not have a chat channel at a button, you should Play (VCR only) or Power instead.

Here is a Code List on PDF that shoud be universal for most remotes. It worked for me.
http://www.remotecodelist.com/remot...ps-Magnavox_PM525S.pdf

Hope this helps you out, good luck.

hey i got the same remote.. how do you operate it

Try these APEX TV codes 0023 0223 0123 0741 Thats from the CL034 Code book

www.remotecodelists.com hope that helps .........T.

I NEED THE CODE OF MY REMOTE CONTROL PHILIPS RC-2835/01...PLEASE HELP US! WE NEED THE TV!

I have the same tv and remote that you do. I went on Philips website and they have instruction manuals and the code lists. You can also press and hold the 'CODE SEARCH' button until the light stays on. Then press 'TV' button. Make sure your TV is on and press Channel Up button until the channel changes on your TV. If you go too far, press the Channel Down button until it changes again. Then press the Mute button to store the code. Good Luck!!