Question about MSI Wireless-G RG54G3 Router

2 Answers

When trying to reset router and reset it up;

It gives me a message that someone is already logged on. and will not allow me to reset. Can you help me?

Posted by on

2 Answers

Re: When trying to reset router and reset it up;

This problem happens after the router has been reset over and over. I have reset many routers in the past but this router keeps saying someone is logged into it after reset.

Posted on Dec 26, 2007

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 317 Answers
Re: When trying to reset router and reset it up;

Any and all routers have a reset button. press and hold it for 10 seconds, then let it go.

The default passwords are:
username: admin
password: admin

Posted on Dec 23, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

Cannot configure belkin router

Locate the reset button on the back of the unit near the ac jack. Press and hold for 15 seconds. That should reset everything including the password. You will then need to reconfigure - leave the password blank initially then change as desired after it logs you in

Dec 09, 2013 | Belkin Routers

1 Answer

Cant find password for Belkin F5D9230-4 G plus mimo router

If you are talking about the password to log in and make changes to router settings, according to the user manual for this router, found HERE, the default password is no password, in other words, leave it blank. If that doesn't work that means someone put a password on it and you will need to reset the router in order to log back in and make changes. If you need help with that, refer to the manual, or reply back to this message and I will help walk you through it.

Jul 01, 2011 | Routers

1 Answer

I want to get the password

I assume you're trying to login to the admin section to set up your router.

Most routers by default use (username, password):
admin, admin
admin, password
admin, (blank)

If your router has already been setup, but you forget the password, then you can try resetting.
There will be a small button on the back panel of the router labeled "reset". It's quite small, you'll need to use a paper clip or the tip of a pen to push it.

Give the router a few minutes to reset itself and to power up again. It is not reset to factory default settings. Try logging in with the suggestions above.

Mar 07, 2011 | Routers

2 Answers

Someone changed my mums password but wasnt her now when she tried clicking forgot password facebook sent her message saying they blocked her account because of too many password resets when she has done...

Perform a hard reset by pressing the button behind the small hole (use a paper clip) as you power it on. That will reset the router to it's factory settings. From there you can log in with the default password. Of course, you'll to reconfigure it from scratch but at least you'll be in control again. Be sure to change the password to something more secure.
Also, some routers will allow you to deny configuration access from wireless clients.

Mar 04, 2011 | Routers

2 Answers

How do I find the access code so someone else can log on and use my wireless internet connection?

Contact you ISP...they will give you either you IP address to log on to access the network settings or they will just give you the password over the phone.

Mar 26, 2010 | Zyxel (91-004-361002) Wireless Router

2 Answers


You can do a reset on the Router to return to factory default. You can press the tiny reset button using any pointed object or with a paper clip. After that, you can already login to the router using default access. Open in a browser and use "admin" as username and "password" as your password.

Nov 19, 2009 | NetGear WGR614 Router

1 Answer

D Link DIR-300 - Connection was Reset - Unable to set up router

press reset button for 10 seconds then all settings are defaults.
you can access your router witrh following link or

Jul 14, 2009 | D-Link Dlink DI-514 Air Wireless 2.4 GHz...

1 Answer

Cannot log into internet after reseting the router

well resetting the button at the back of the router makes the router go to factory default settings.As such you need to configure the router once again as per your service provider's settings.If you already have the IP informations and the other informations.You can try to log into the router using the default IP of which would take you to the router home page.You can configure the Router and save the same.Once done you should be good to go.

Apr 13, 2009 | NetGear DG834G Router

1 Answer

Need to get into the router settings , but the default username and password aren't working, I've already held the reset button down for 30 secs and tried login admin:password , but no luck...

Since you already tried steps 1 thru 4, give steps 5 and on a try

Write down configuration information such as IP addresses, security keys, opened ports and services, etc., that you modified. (The default username is admin and the password is either password or 1234. Try these before resetting the router.)
  1. Press the reset button on the back until the test light blinks. This takes about 10 seconds. (To avoid accidental resets, the small button is recessed. Use a pen or paperclip to access it.)
  2. Release the button.
  3. Wait for the router to reboot.
  4. Log in with the default password. If the router was not cleared, try these additional steps AFTER the router has finished rebooting.
  5. Unplug the router's power.
  6. Press and hold the reset button. While the button is held down, reconnect router's power.
  7. Continue to hold the reset button for 20 seconds after reconnecting the power.
  8. Wait for the router to reboot.
  9. Log in with the default password.

Mar 05, 2009 | NetGear RangeMax WPN824 Wireless Router...

5 Answers

DI-524 problem please help

The default username for this router is "admin" without the quotes, and the password is blank (don't type anything.) If that doesn't work, it may have already been changed, in which case you can soft reset the settings to factory defaults by using the reset button on the back of the box.

Sep 24, 2008 | D-Link AirPlus DI-524 Wireless Router

Not finding what you are looking for?
MSI Wireless-G RG54G3 Router Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top MSI Routers Experts


Level 3 Expert

6993 Answers

Chris Hunt

Level 3 Expert

1342 Answers


Level 3 Expert

4506 Answers

Are you a MSI Router Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides