Question about Hobart Handler 140 Mig Welder

1 Answer

I need a replacement circuit card for my hobart handler 175..the number is 195887..where can I get one?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 92 Answers

Go to Hobart

Posted on Oct 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need Q1 transistor for 135 hobart welder


The transistor is mounted on the main circuit board, you cannot buy the part from Hobart or Miller, they only sell the complete circuit board.
If you can read any part numbers from the transistor you can purchase the part from a electronic parts supplier.

Jul 13, 2014 | Hobart Handler 140 Mig Welder

1 Answer

Drive motor for hobart 125


Your Hobart has a Drive Motor Protection.The Drive motor protection circuit protects drive motor from overload. If drive motor becomes inoperative, release gun trigger and wait until protection circuit resets allowing drive motor to feed wire again. Or you can reset it manually by pressing the reset button located on the back welder. If these actions does not work then here's the part number for your motor:HOB 239696.Check our website for pricing you need to call since this is an old welder and pricing needs to be search at Hobart Co.
http://www.praxairdirect.com/webapp/wcs/stores/servlet/TopCategories1_10152_10051_-1

Nov 21, 2011 | Clarke Power Products Clarke 130EN Mig 110...

2 Answers

My Hobart Handler 120 needs a .045 wire drive wheel. Where can one be purchased?


Locate your locale Hobart welding distributer, or contact hobart, the are nice people and will give you all the avice you need.

Dec 26, 2009 | Hobart Handler 140 Mig Welder

1 Answer

Hobart Handler 175 Wire doesn't feed when trigger operated.


First, UNPLUG the Welder! There is a small control board (2"x2") that the feed motor plugs into, it has a fuse on it. Here is what you do: Follow the circuit board trace that goes from one side of the fuse though a resistor then to the connector full of wires on the edge of the board, check that resistor for continuity it should read some value besides open. If it is open, this is your problem (as the drive motor ages it draws slightly more current than new, which should blow fuse, but instead blows the resistor). The resistor should be replaced with same resistance value, if problem persists replace again but instead of 1/4amp bump up to a 3/4amp for $1 or replace that drive motor for $150, you choose. Good Luck!

NOTE: As with any circuit board, take precautions to prevent ESD damage to board.

Apr 20, 2009 | Hobart Welding Tools

2 Answers

Hobart handler 140 will not feed wire


A schematic would certainly help, give Hobart a call and ask for a wiring diagram. or manual. Hobart are very helpful and may even give you guidance, you may have to pay the postage, they usually fax these documents so it will not cost you anything.

Feb 13, 2009 | Hobart Handler 140 Mig Welder

Not finding what you are looking for?
Hobart Handler 140 Mig Welder Logo

Related Topics:

546 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Welding Tools Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Troy
Troy

Level 1 Expert

35 Answers

Are you a Hobart Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...