Question about Rosewill R900J 19" Flat Panel LCD Monitor

2 Answers

Screen goes black

Compaq Presario 7317 - screen goes black after a few seconds. Greem power light still on. If I turn the power light off and then on, the screen appears for about 15 seconds and then goes black again.

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 or more questions within one hour.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.

  • Expert
  • 83 Answers
Re: Screen goes black

It's an LCD so the problem is most likely the back-light inverter board. Take a flashlight and shine it directly into the screen from the front. Can you see the image on the screen now? If the image is there but you can't see it without the flashlight than the inverter board needs to be replaced. This is a VERY common problem. Good Luck and let me know what happens, His Dudeness

Posted on Jan 21, 2015

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers
Re: Screen goes black

Do you see any dull image on the screen ?
If yes the inverter Card/Backlight of the screen is having problem.


Posted on Dec 22, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer


Does it turn on? Check the power cord and monitor connections for power, monitor and computer.

Jul 12, 2010 | Compaq FP 7317 17" LCD Monitor

1 Answer

My screen goes black occasionally. I unplug it

There could be some faulty capacitors on the inverter board which are buldging or leaky.

May 24, 2010 | Compaq FP 7317 17" LCD Monitor

1 Answer

The monitor goes black while on

Open it up and look at the capacitors. The round "tin can" looking components. If the tops appear bulged, then replacing them may help. Check out the YouTube video... and web site...

Good Luck!

May 12, 2010 | Hannspree HannsG HG281DP 28" LCD Monitor

1 Answer

My monitor goes to black. i power off and on and

Your problems describe a bad Power Inverter. It's a small circuit bard inside the monitor, it powers the CCFL lamp of your monitor. Could be cheap to replace, but in most cases you just buy a new one. It could also be a bad CCFL lamp.

Mar 14, 2010 | HP Compaq FP 7317 17" Flat Panel LCD...

1 Answer

Monitor turns on and screen comes up for about 1 second and then turns black. Green power light stays on and green

This will be a fault with the inverter section that powers the ccfl lights usually a transistor or an i.c replaced will cure the problem

Dec 22, 2009 | Compaq FP 7317 17" LCD Monitor

1 Answer

Our compaq monitor will not go on. It is plugged in and the green light goes on when the button is pushed, but nothing comes up on the screen after moving the mouse. Our Presario computer is turned on. Any...

Make sure it is properly plugged into your computer too. (blue headed cord) should go from the screen to the computer. Make sure the cord is not damaged.

There should be a total of two cords needed (one for power (black) and (one from the computer to screen (usually blue))

Oct 18, 2009 | Compaq 15 COLOR MONITOR***

3 Answers

Fp 7317

My monitors green light stays on, but the screen will come on for a second then goes off
comaq fp737

any ideals

May 15, 2007 | Compaq FP 7317 17" LCD Monitor

3 Answers

Compaq FP 7317

see the data cable is properly connected

Sep 09, 2006 | Compaq FP 7317 17" LCD Monitor

1 Answer

Nothing on the screen after power on

Turn on the computer and complete the following steps: Step 1: Check cable connections (If you can see the initial HP or Compaq logo screen but later lose the picture, you can skip to Step 2.) check the video cable connection on the back of the computer and on the monitor. Make sure that it is connected properly and the connecting screws are tight. Turn the monitor off and then back on again (while the computer is on) to see if an image appears. Some Flat Panel monitors have two similar power input connections placed side-by-side on the back of the monitor, which sometimes allows them to get confused for one another. One connector is used to supply power to the speakers with a separate power cord, while the other connector is used for the monitor's power adapter. Ensure that you have the monitor's power adapter cord plugged into the power connector and not the speaker connector. After you have reconnected the power cord, turn on the monitor (while the computer is on) to see if an image appears. If there is still no image, continue to the next Step. Step 2: Resetting the monitor At first setup, or under certain signal conditions, the monitor may not be able to switch to a new display resolution. Do NOT shut down or restart the computer. Instead, perform the following steps: Turn off the monitor using the Power button on the front. If the Power button does not respond, unplug the power cord from the back of monitor and wait five seconds. Plug the power cord back in. You should see the image from the computer on the screen.

Jan 05, 2006 | HP Compaq FP 7317 17" Flat Panel LCD...

Not finding what you are looking for?
Rosewill R900J 19" Flat Panel LCD Monitor Logo

Related Topics:

2,220 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rosewill Computer Monitors Experts

Jim Parker
Jim Parker

Level 3 Expert

1040 Answers


Level 3 Expert

56548 Answers

Mike Butler
Mike Butler

Level 3 Expert

6674 Answers

Are you a Rosewill Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides