Question about AEG Lavamat 16810 Front Load Washer/Dryer

1 Answer

The mashine does not pump the water out. - AEG Lavamat 16810 Front Load Washer/Dryer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Pump may b nakerd or fiter trap may b blockd

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mashine fills with water


check the program dial or settings. Put the machine off. then the water slot should close. If it does not close it is defect and you should ask a tech to replace it, or buy a new machine.

Mar 24, 2015 | Washing Machines

1 Answer

PUMP REPLACEMENT


Possible that the hose link to the drain is loose, the drain pump is defective and leaking or the rubber door gasket is faulty. Please take a good view

May 02, 2013 | EuroTech Washing Machines

1 Answer

My new omega washing mashine shows an E2 error code 5 miniutes into the wash how do I fix this?


Hello,

Manufactured by omega washing mashine have an electronic controlpanel that must be unlocked in order to set or make changes to your washingcycle.
E2 indicates a water leak. When a leak occurs, it trips thefloat device by dumping water into the dishwasher's base. The incoming watervalve will be switched off, and the drain pump will turn on until the sump isempty
However, if an error light is blinking on your dishwasher'scontrol panel, the panel must be reset before you can gain access. Blinkinglights on your washer control panel may signal a mechanical problem that needsto be repaired. If the lights continue to blink after you've reset the controlpanel, contact Sears to service omega washing mashine or considertroubleshooting the appliance yourself carefully.Instructions
1 Press and hold the "Heated Dry" button onyour omega washing mashine for four seconds to unlock the dishwasher controlpanel.
2 Press the "Heated Dry," "Normal Wash,""Heated Dry" and "Normal Wash" buttons one after theother, in fairly quick succession.
3 Wait for the washer to run a short diagnostic test.
4 Press the "Cancel/Drain" button at the endof the diagnostic test cycle. This should reset the control panel on your omegawashing mashine. Thankfor using fixya.

Jul 30, 2011 | Washing Machines

1 Answer

How can I control the presure of the water drain in the washer mashine


Only way to reduce pressure is to reduce efficiency of pump. i.e. reduce voltage supplying pump winding. Could reduce flow rate by restricting outlet hose diameter but not a good idea as could effect peformance of washing machine and overload pump, belt or brake.

Apr 02, 2011 | Ovens

1 Answer

It will wash but water will knot spin out


Hi is the mashin spin but the water not out?
check the water pump maybe some thintk in it

Oct 27, 2010 | Washing Machines

1 Answer

From time to time the mashine is not evacuate the water and the mashine will not start for a new load .I have to unscrew the filter,drain the water and then will wash. Is a problem with the pump? thank you...


a front loader huh, usually there is an access panel at the bottom front held on with 2 screws. remove this panel and trhere should be a trap filter that is plugged up. remove filter and clean it out, than put it back. or the water pump is going bad try the filter first.

Nov 07, 2009 | Whirlpool LHW0050PQ Front Load Washer

1 Answer

F2 and beeping sound when started


F2 indicates

WATER Leakage - Water is in drip tray

Floater switch (water leakege detector switch) detects water leakage,
then draining pump is switched on for fixed time or until water indicator reports
that mashine is empty depending on model


remember to unplug it from power if any repair is done

Best regards and good luck

Oct 03, 2009 | Whirlpool Dishwashers

1 Answer

Zanussi washing mashine


Plug off the wall. Open up behind, you will find a thin tube, maybe tranparent or black coming down from the control panel to the exit area (pump area) of your machine. Carefully disconnet this from above and blow into it, it should be free, if not clear it, if kinked or broken replace.

If this does not work, its your solenoid valve at the entrance point of your machine, top right, where the water is received. Just change this. If all works fine rate me please.

Dec 27, 2007 | Washing Machines

Not finding what you are looking for?
AEG Lavamat 16810 Front Load Washer/Dryer Logo

Related Topics:

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1460 Answers

Einar Axel...
Einar Axel...

Level 1 Expert

12 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18391 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...