Question about NAD C320 2-Channel Amplifier

Open Question

My NAD C320BEE suddently made some funny "ts-ts" sound then all channels disconnected. What's wrong. I have been using this product in Japan for about 3 years. Could the 100V voltage a problem?

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
marsrover
  • 682 Answers

SOURCE: The right channel on my NAD intergrated amplifier C320Bee no longer works.

if you did test for your cable and speaker and you find it fine-your problem will be in output stage of your amp and needs aid of service center.

Posted on Jul 15, 2008

Ad
marsrover
  • 682 Answers

SOURCE: connecting sub with nad c320bee

pre out from nad---------to 2 rca input in sub.

Posted on Jul 23, 2008

gopakumarg43
  • 74383 Answers

SOURCE: nad c320bee keep over heating

Hello
Disconnect all speakers and switch ON the set without any input connected, and see whether it heats up. A moderate heat is permissable, but should not over heat. If it overheats without any load or input connected, the set need service. OK.

Posted on Jan 19, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nad c320bee keep over heating


Hello
Disconnect all speakers and switch ON the set without any input connected, and see whether it heats up. A moderate heat is permissable, but should not over heat. If it overheats without any load or input connected, the set need service. OK.

Jan 19, 2012 | NAD Audio Players & Recorders

1 Answer

My NAD T65 receiver has problems with the digital sound input. The sound gets choppy when I increase the volume. It seems to be ok at very low volumes, but as soon as I crank it up it fails. It happened...


Could the amp be showing distress, clipping, going into protection? There really isn't much reason for volume of a digital input to have an effect unless the room is shaking so much it's upsetting the digital source device's tracking.

http://www.retrevo.com/support/NAD-T765-Receivers-manual/id/23031ag215/t/2/

Aug 15, 2011 | NAD T765

1 Answer

I have a sharp crt tv model:25c-bs370,although i'm using cable signal which more than 100 channels,still the channel it receive is limited only to 35 channels...how to rechannel the unit?my tv came...


Hi,The Television from japan have no lowband channel,It can be rechannel but the channel additional is onlly the lowband channel it maybe add only 2 channel.So the best things you do is to buy and install a channel converter to your TV.A channel converter is 100 plus channel thats why you can use your cable to japan television.To install the channel converter you need to set your television to Video setting and use RCA connector and plug it to video/sound input of your TV and video/sound output of channel converter.The cable connected plug it to channel converter.

Jul 11, 2011 | Sharp Televison & Video

2 Answers

NAD C320 BEE - goes silent. Only yellow light.


Hi,
Just came accross your post accidentically, while reparing my own C320BEE. May be it 's too late for you now, but it could help others: I had the very same symptoms as you described and after a long search found out that the trouble was R45 in one of the 18V regulators. (R45: 33 ohms 1/2W fuse resistor, situated more or less half-way between the two "metal towers" on the main board. Replace by a somewhat stronger type 1W or so.
Likewise R46.)

Dec 23, 2009 | NAD C320 2-Channel Amplifier

1 Answer

NAD 775 will not play surround sound from XBOX


try to calibrate the speakers from audessy rom menu,i did it and it lokes like it just needed to register all the channels,hope it helps.

Jan 29, 2009 | NAD T753 Receiver

1 Answer

Connecting sub with nad c320bee


pre out from nad---------to 2 rca input in sub.

Jul 22, 2008 | NAD C320 2-Channel Amplifier

1 Answer

The right channel on my NAD intergrated amplifier C320Bee no longer works.


if you did test for your cable and speaker and you find it fine-your problem will be in output stage of your amp and needs aid of service center.

Jun 11, 2008 | NAD C320 2-Channel Amplifier

1 Answer

Carver TFM -35


possible short in speaker system. Disconnect the speaker to that channel. if it does not click off then you have a short outside the amp in your wiring or in the speaker.

Sep 17, 2007 | NAD C350 2-Channel Amplifier

Not finding what you are looking for?
NAD C320 2-Channel Amplifier Logo

Related Topics:

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top NAD Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5156 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a NAD Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...