1 Answer

Power to the box but fuse keeps blowing.

I have a Jandy Aqua Link RS8. The fuse in the outside control box shorted out when I was turning the unit on and off when backwashing. I replaced the fuse, a 3.15 amp, 250 V?. It ran awhile but the blew again. Is there another fuse somewhere. This one is on the main board.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Yes their are 2 fuses on a aqualink. most fuses are clear mome are white make sure the fuse was the same, becuase a white fuse will burn slower, take more heat.

Posted on Oct 05, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Aqua link rs8

need more info what do you need?

Jul 11, 2014 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

1 Answer

Jandy aqualink rs beeping

need more info does it have a aqua pure if so it must no0t be working turn chlorine production to 0 and it will not beep

Oct 17, 2013 | Jandy AquaLink RS OneTouch RS8 Pool or Spa...

1 Answer

I have an AquaLink RS8. The display reads "6520

check red 4 pin plug if ok check wires to controller if ok bad PCB board

Jul 28, 2011 | Aqua Pool & Spa

1 Answer

The fuse on my circuit board keeps blowing after a thunder storm. Need to replace the entire circuit board for my RS8 system. Any sugestions on where I can purchase just the circuit board? Mike

unplug all the aux plugs but mark them replace fuse turn on if it still blows need a new board if not plug in auxs 1 at a time till it pops then check out that aux for shorts sometimes the relays short out

Mar 17, 2011 | Jandy AquaLink RS OneTouch RS8 Pool or Spa...

3 Answers

We had an intense thunder storm and lightening the other night. My indoor Aqualink RS8 has a blank screen and is unresponsive. It apparently is not getting any power. The Spalink controller is blinking...

The circuit internally have gone short.There are many other facing this same problem.Some have got this indoor panel dead due to moisture collected on the indoor panels circuit board.The panel is not very strong to handle the humidity effect.It gets short. It has to be replaced. To get any other part and also the indoor panel board please click on the link below ------ Thanks.

Jul 19, 2010 | Jandy AquaLink RS OneTouch RS8 Pool or Spa...

1 Answer

Jandy Aqualink RS8 All Button randomly turns on Spa

Unfortunatly you have a bad circut board. Which is very expensive. One good thing though, you will upgrade the unit when doing so.

Aug 22, 2009 | Pool & Spa

1 Answer

No power at the power panel( Aqualink RS8)

if unit comes on write down all auxs then remove plugs replace fuse turn on then plug one in at a time till it blows then you know which auw then see if wires are burnt


Not finding what you are looking for?

676 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

8175 Answers

Craig Butler
Craig Butler

Level 3 Expert

1723 Answers

Jay Finke
Jay Finke

Level 3 Expert

1383 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides