Question about House Brand Car Audio & Video

1 Answer

Speaker removal on 2005 explorer sportrac ? getting the grill off the front door and speaker removal

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 69 Answers

I have attached a link with a how-to that has pictures so that you can get a better idea.

1. remove the window/lock switch panel by pulling upward at the front of the switch(held in by clips)careful not to break the tab towards the rear(see pic) unplug and remove
2. remove screw behind that panel
3. remove trim around the door handle, and screw behind that panel.
4. remove 2 screws at the bottom of the door panel
5. then pull straight up and towards you in one motion

http://www.explorerforum.com/forums//showthread.php?t=192049

hope this helps

Posted on Oct 05, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove door panel on 2014 Buick Verano


Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door. Remove the three screws retaining the front door trim panel to the front door.

Feb 16, 2016 | Buick Verano Cars & Trucks

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How do i car door panels safely


  1. Remove the cover behind the inside door handle.
  2. Remove the screw from the bottom of the pull cup retaining the front door trim panel to the front door.
  3. Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door.
  4. Remove the three screws retaining the front door trim panel to the front door.

Do not attempt to remove more than one pushpin at a time.

  1. Use a suitable tool to remove the pushpins from the door.
  2. Carefully lift the door panel away from the door.
  3. Detach the electrical connectors as necessary and remove the panel from the door.

To install:

  1. Installation is the reverse of removal.
Door Panel

This procedure applies to both the front and rear door panels.


// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_23.gif

Remove the cover from behind the inside door handle by gently pulling it out to release the retaining tabs


c17hydro_24.gif

Remove the pull cup retaining screw cover and...



c17hydro_25.gif

... remove the retaining screw from the cup and lift the cup straight up out of the door panel



c17hydro_26.gif

Remove the two sail panel/speaker grille retaining screws and...



c17hydro_27.gif

... remove the panel/grille from the door



c17hydro_28.gif

The door panel is retained to the door by 11 retaining clips



c17hydro_29.gif

Carefully lift the door panel off of the door and...



c17hydro_30.gif

... detach the electrical connectors from the switches and remove the panel from the vehicle

Nov 13, 2010 | 1996 Ford Taurus

1 Answer

How do you replace the regulator for the power window on the 2002 ford explorer


Regulator - Power Windows - Front Door
  1. Remove the front door trim panel as follows:
    1. Remove the front door handle bezel.
    2. Remove the front door window/lock control switch bezel.
    3. Disconnect the window/lock control switch electrical connectors.
    4. Remove the 3 front door trim panel screws.
      CAUTION To avoid damaging the trim panel, do not pull directly outward to carry out this step.
    5. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    6. Remove the exterior mirror control switch from the front door trim panel.
  2. Remove the front door speaker.
  3. Remove the interior molding.
  4. Disconnect the door lock actuating rod at the door handle assembly:
    1. Release the door lock actuating rod clip.
    2. Position the door lock actuating rod aside.
  5. Remove the front door weather shield.
    CAUTION Make sure the holes in the glass bracket do not become enlarged during the rivet removal process. If the holes become enlarged, the new rivets may become loose, resulting in clicking noise concern.
    NOTE Some vehicles may use rivets to attach the window glass to the window regulator assembly. Use a 4.5 mm (0.1772 in) drill bit to drill out the glass-to-regulator rivets.
  6. Remove the 2 front door window glass-to-regulator bolts or rivets.
  7. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets.
  8. Secure the front door glass in the full up position with tape.
  9. Disconnect the window regulator motor electrical connector.
  10. Remove the 4 window regulator assembly nuts.
  11. Remove the window regulator assembly.

    0b00886.jpg

    Fig. Exploded view of the front door and power window components-2005 Explorer and Mountaineer

To install:
  1. Position the window regulator assembly.
  2. Install the 4 window regulator assembly nuts. Tighten to 89 inch lbs. (10 Nm).
  3. Connect the window regulator motor electrical connector.
  4. Remove the tape securing the front door glass in the full up position.
  5. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets. Install the bolt and tighten the bolts to 62 inch lbs. (7 Nm), or install new rivets.
  6. Install the front door weather shield.
  7. Connect the door lock actuating rod at the door handle assembly:
    1. Position the door lock actuating rod into proper location.
    2. Attach the door lock actuating rod clip.
  8. Install the interior molding.
  9. Install the front door speaker.
  10. Install the front door trim panel as follows:
    1. Install the exterior mirror control switch from the front door trim panel.
    2. Position the door trim panel onto the armrest to engage the panel clips.
    3. Install the 3 front door trim panel screws.
    4. Connect the window/lock control switch electrical connectors.
    5. Install the front door window/lock control switch bezel.
    6. Install the front door handle bezel.

  1. Raise the front door window glass to the full up position.
  2. Remove the interior door handle.
  3. Support the front door window glass.
  4. Disconnect the front door window regulator motor electrical connector.
  5. Remove the equalizer bracket nuts.

    4945f24.jpg
    Fig. Remove the equalizer bracket nuts-2005 Explorer Sport-Trac
  6. Remove the front door window regulator by removing the rivets and nuts.
  7. Remove the front door window regulator motor retaining bolts and then remove the motor.

    52a6816.jpg

    Fig. Remove the front door window regulator motor retaining bolts and then remove the motor-2005 Explorer Sport-Trac
To install:
  1. Installation is the reverse of the removal procedure.
  2. Tighten the regulator motor mounting bolts to 8 ft. lbs. (11 Nm).

Hope this help (remember rated and comment this).

Mar 24, 2010 | 2002 Ford Explorer

1 Answer

How do you change the front speakers on a renault clio grande 1999 with electric windows. not sure on how the front grill for speaker is removed.


the grill is fixed to the door trim .take off door trim carefully.speaker/s are fixed to door frame simply take out/swop over speaker make sure they are fixed securely/dont vibrate....

Feb 11, 2010 | 2005 Renault 18I

1 Answer

How to replace front speakers in a daewoo leganza 02


You will need to either remove the door card or the speaker grill on the door card. To do this you will need a set of thin nose pliers for removing door clips, a flat head screw driver and a phillips screw driver for any cross head screws. Use the flat head screw driver to pop the grill off, if the grill is not removeable you will have to take the whole door card off. To do this you need to remove the electric windows panel as well as the door handle and lock panel, from their disconnect them from their harnesses. Then remove all clips and screws holding the panel in place. The door card should come free without too much effort, pulling upwards and away from the window. Unscrew the old speakers and disconnect the wires from them. Wire your new speaker to the same wire configuration as the old one. Screw it in. Place the door card back on and then plug the harnesses back in and place the door lock and window locking panels back in place. Do the same for the other door.

A professional installation will cost about $80 I think, I did my door speakers on my car and all I had to do was pop out the grill so it was easier than I expected.

Jul 17, 2009 | Car Audio & Video

1 Answer

Where is the O2 sensor on a 2005 Explorer Sportrac?


the o2 sensor is always located in the exhaust sys. usually near the manifold Note some vehicles have 2 sensors on located near the cat. converter

Jul 05, 2009 | 2005 Ford Explorer Sport Trac

1 Answer

Replace speakers on Ford Explorer Sport Trac


The front and rear door panels must be removed. The interior door handle will have to be removed, and the power window switch will also have be removed. This is held in by metal clips that secure it to the door panel. Do not be afraid to use a little force to get under the switch panel, and pry it from the door panel. Once you have all accessories off of the door panel, look for what may appear to be "plugs" in the door panel. These may conceal the presence of a screw. Also, check around the interior door pull for screws or "plugs". When this is done, use a medium to large screwdriver, or a trim removal tool, and start prying the door panel away from the door. Start at the bottom, and work your way around the door, until you get about 2-3 inches from the top of the panel where it meets the window. When you are at this point front and rear, simply lift up on the door panel, and it should come off easily. Once the panel is removed, you will easily find the speakers.

Nov 11, 2008 | 2005 Ford Explorer Sport Trac

1 Answer

Replacing front door speakers


You need to pull the door panel to get to the speaker. It is bolted to the door shell, not the door panel.

Sep 18, 2008 | 1996 Toyota Avalon

1 Answer

Replacing front and rear speakers in a 1999 Mazda Protege


Whats the problem?

Back - Remove speaker grill, unscrew, climb in trunk, unplug - remove.

Front - Remove speaker grill, unscrew, pull out, unplug. If you have problems remove window winders and door skins

Dec 15, 2007 | Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top House Brand Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4848 Answers

yadayada
yadayada

Level 3 Expert

75817 Answers

The Knight
The Knight

Level 3 Expert

74118 Answers

Are you a House Brand Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...