Question about Cisco 1811 Router

4 Answers

Can not login on con 0 port (not text), lost

Cisco 1811 router, can not login on con 0 port (not text), lost password, Router never used, lock out, is there a way to reset , busy green led light stays lite, is this normal, please help, thanks mike

Posted by on

  • mikebobski Oct 03, 2009

    it is a cisco router, that was given to me and was config before, and do not know ip addresses on ports,dont know password, try to get into con 0 port to do password recovery, but they must of shut port down, what to know is ther another way into router

×

Ad

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 329 Answers

Default username and password for all router are

admin and admin

or

admin and password

try these two combinations

else try link

http://www.cisco.com/en/US/products/ps6187/index.html

Posted on Oct 03, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 39 Answers

This is a cisco router, there are no combinations of admin anything that will work, unless by some luck the user before you specifically added the the user admin.

The default username and password for a cisco box is cisco for both the username and password. If con0 is disabled you must attach via con0 anyways and reboot the router and begin the cisco documented password recovery.

http://www.cisco.com/en/US/products/ps6187/index.html

Posted on Jan 24, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 39 Answers

Use aux port or change the con port.

Posted on Oct 06, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 33 Answers

If the router has never been used before then manually plug in a cord from the router to your computer, then restart your computer, then when your computer starts up again goto internet explorer and type in the address bar 192.168.1.1 and then you should be in your routers main screen. To enter the router type ADMIN as the username and password. and it will take you step by step through there!

If you need more help just e-mail me at dubcars101@yahoo.com

Posted on Oct 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a Cisco router password?


If you forget the default password for the Cisco router, first you will need to reset the router for default settings.
After resetting your Cisco router to default settings, go and access the configuration page using the IP address 192.168.0.1
After successful login to Cisco router login page, go for the "Menu" and from here you can find the option to change the password for the Cisco router.
other question, you can visit http://www.router-switch.com/, you can also buy brand new Cisco routers/switches with big discount here.
thank you

Oct 20, 2017 | Cisco Computers & Internet

Tip

Cisco 1800 Series, Business Router for Small to Medium Sized Business/Enterprise


Cisco 1800 Series Integrated Services Routers, the next evolution of the award-winning Cisco 1700 Series modular access routers, own more advantages than the formers. Cisco 1800 series, ideal for small to medium-sized businesses and small enterprise branch offices, enable businesses to reduce costs by deploying a single, resilient system for fast, secure, delivery of multiple mission-critical business services, including data, security, unified communications, wireless.<br /><br /><a href="http://www.router-switch.com/Price-cisco-routers-cisco-router-1800-series_c17">Cisco 1800 series router</a> has several models including 1801, 1802, 1803, 1811, 1812, 1841(most popular), 1861, all of them have some common features: a. Designed for small businesses or branch offices and to offer secure wireless networking; b. Multiple performance options based on local, remote, or broadband connections; c. Integrated security including encryption and protection against hackers; d. Virtual private networks for linking to partners, suppliers, and remote offices; e. Multiple options for adding reliability and option for reduced costs by using power from network cabling; f. Software upgrades to add new features and functions, and integrated switching capabilities.<br /><br /><a href="http://www.router-switch.com/Price-cisco-routers-cisco-router-1800-series_c17">Cisco 1800 series</a> router has several models including 1801, 1802, 1803, 1811, 1812, <a href="http://www.router-switch.com/cisco1841-p-97.html">1841</a>(most popular), 1861. You can check details of every type as follows:<br />The fixed platform models (1801, 1802, 1803, 1811, 1812) include multiple WAN interface options, plus:<br />Up to broadband speeds<br />Eight 10/100 Mbps built-in switch ports with optional Power over Ethernet (PoE), for providing DC power to network devices such as IP phones<br />Up to 50 VPN tunnels<br />Support for wireless local-area network (LAN) standards 802.11a/b/g<br /><br />The 1841 is a modular platform with a wide range of interface options, plus:<br />Up to T1/E1speeds<br />Up to four 10/100 Mbps built-in switch ports<br />Up to 800 VPN tunnels<br />Support for wireless local-area network (LAN) standards 802.11a/b/g<br /><br />The 1861 is a modular platform built on a fixed base with a wide range of WAN interface options, plus: <br />Integrated Cisco Unified Communications Manager Express or Cisco Unified Survivable Remote Site Telephony for call processing<br />Cisco Unity Express, for voice messaging and automated attendant<br />Integrated LAN switching with Power over Ethernet (PoE) expandable through Cisco Catalyst Switches<br />Onboard voice ports for PSTN, PBX, and key system connections<br /><br />With Cisco 1800 Series integrated services routers; you can lay the foundation for future growth and prepare for voice, video, wireless, and security solutions tomorrow. <br /><br />If you want to know more about e about the certain type of Cisco 1800 series, you can visit the list of Cisco 1800 router series, prices also offered.<br /><br />

on Jun 30, 2011 | Computers & Internet

1 Answer

How do I reset my password?


In the below example i'm setting password as cisco for enable mode & Virtual terminals of router
1)Connect to the router and follow the below steps
Router>
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret cisco
Router(config)#line vty 0 4
Router(config-line)#password cisco
Router(config-line)#login
Router(config-line)#exit
Router#exit
Router con0 is now available
Press RETURN to get started.


Test:
Router>enable
Password: (type cisco to enter into the router privilaged mode)
Router#

Aug 09, 2015 | Computers & Internet

1 Answer

Cisco E3200 router configuration lost


The Cisco connect software came on the CD in the box with the router. If was used to configure the router when new. This can be used to fix the router now. I could guide you through a manual configuration but the software is a much faster easier method. I would recommend you try that route. Get the CD and run from there if you are worried about phishing.

Feb 12, 2014 | Linksys by Cisco Linksys E3200 Dual-Band N...

1 Answer

SMCWGBR14 N only power led


Resolutions:
1) Power on the SMC modem / router and wait until all the lights are light up.
2) Press and hold the reset button for 15 seconds and wait until all the lights are light up as the modem / router needs to reboot.
3) Try to access to the admin page again by default login IP - http://192.168.2.1/.
4) Enter the default login password.
a) smcadmin
b) (blank)
c) barricade

Nov 25, 2013 | Edge Barricade 4 Port Broadband Wireless...

1 Answer

I forgot a password and i cant access a catalyst 2960 24-port 10/10


You can only reset password this way:
1.
Attach a terminal or PC with terminal emulation (for example, Hyper Terminal) to the console port of the switch.
Use the following terminal settings:
  • Bits per second (baud): 9600
  • Data bits: 8
  • Parity: None
  • Stop bits: 1
  • Flow Control: Xon/Xoff
2.Unplug the power cable.
3. Hold down the mode button located on the left side of the front panel, while you reconnect the power cable to the switch
4. Release the Mode button when the SYST LED blinks amber and then turns solid green. When you release the Mode button, the SYST LED blinks green.
5. switch: flash_init
6. switch: load_helper
7. switch: dir flash:
8. switch: rename flash:config.text flash:config.old
Rename config.text to config.old. In that file the password is stored.
9. switch: boot
10. Enter "n" at the prompt to abort the initial configuration dialog
11. Type en to enable
12. Switch#rename flash:config.old flash:config.text
13. Switch#copy flash:config.text system:running-config
14. Overwrite the current passwords:
conf term
enable secret <new pass>
enable password <new pass>
line vty 0 15
password <new pass>
login
line con 0
password <new pass>

15. write memory
16. copy run start

Sep 25, 2013 | Cisco Catalyst Computers & Internet

1 Answer

Password


There's a Reset button on back or bottom. Press and hold until the power LED blinks, then release it and the login/password will return to their defaults.

Oct 29, 2012 | Cisco Linksys Wireless N Home Router...

1 Answer

No wireless connection for laptop. Linksys router - model #wrt160n v2


you can run a direct line to that router and go to the cisco web site and get the information you need to run that router. its a pdf format and is 2.56 Meg. Try this

SecureEasySetup (Orange/White) The Cisco logo is the Router's SecureEasySetup button. It

lights up and will stay orange when the Router is powered on. The color orange indicates that

the Router is not using the SecureEasySetup feature, while the color white indicates that the

Router is using the SecureEasySetup feature. When the Router enters SecureEasySetup

mode, the Cisco logo will turn white and start flashing. After the Router has generated

the SSID and WPA Personal key, the Cisco logo will stop flashing and stay white.

To clear the SSID and WPA Personal key, press and hold down the Cisco logo for five seconds.

The Cisco logo will flash slowly as the Router resets itself. The Cisco logo will turn orange to

indicate a successful reset.NOTE: SecureEasySetup is a feature that makes

it easy to set up your wireless network. If you have SecureEasySetup devices, run the Router's

Setup Wizard CD-ROM and follow the onscreen instructions to use SecureEasySetup.

Power (Green) The Power LED lights up and will stay on while the Router is powered

on. When the Router goes through its selfdiagnostic mode during every boot-up, this

LED will flash. When the diagnostic is complete, the LED will be solidly lit.

DMZ (Green) The DMZ LED indicates when the DMZ function is being used. This LED will

remain lit as long as DMZ is enabled. WLAN (Green) The WLAN LED lights up when

the wireless feature is enabled. If the LED is flashing, the Router is actively sending or

receiving data over the network. 1, 2, 3, 4 (Green) These numbered LEDs, corresponding with the numbered ports on the Router's back panel, serve two purposes. If the LED is continuously lit, the Router is successfully connected to a device through that port. A flashing LED indicates network activity over that port.

Internet (Green) The Internet LED lights up when there is a connection made through the

Internet port. A flashing LED indicates network activity over the Internet port.

Good luck

Nov 26, 2010 | Computers & Internet

1 Answer

Cisco 1811 router freez


replace your router, got a problem with the board...

Jun 18, 2009 | Cisco 1811 Router

3 Answers

Telnet password


Use this step:Router>enable Router#config t Router(config)#line vty 0 4 Router-2(config-line)#login% Login disabled on line 66, until 'password' is set % Login disabled on line 67, until 'password' is set % Login disabled on line 68, until 'password' is set % Login disabled on line 69, until 'password' is set % Login disabled on line 70, until 'password' is set Router-2(config-line)#password newpasword

Mar 08, 2009 | Cisco 800 (CISCO802) Router

Not finding what you are looking for?

Open Questions:

0 Answers

Cisco 1811 router hangs atfer a partial boof: Output shown below: System Bootstrap, Version 12.3(8r)YH8, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 2006 by cisco Systems, Inc. C1800 platform with 393216 Kbytes of main memory with parity disabled Upgrade ROMMON initialized program load complete, entry point: 0x80012000, size: 0xc0c0 Initializing ATA monitor library....... program load complete, entry point: 0x80012000, size: 0xc0c0 Initializing ATA monitor library....... program load complete, entry point: 0x80012000, size: 0x1023778 Self decompressing the image : ################################################################################################################################################################################################################################################################################################################################## [OK] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco IOS Software, C181X Software (C181X-ADVIPSERVICESK9-M), Version 12.4(6)T6, RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Fri 08-Dec-06 13:16 by kellythw Image text-base: 0x80012124, data-base: 0x81F31000 router hangs&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;&gt;.

Feb 27, 2017 | Cisco 1811 Router

Cisco 1811 Router Logo

666 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cisco Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Gareth Tomlinson
Gareth Tomlinson

Level 2 Expert

116 Answers

Are you a Cisco Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...