Question about RC Toys

5 Answers

Yiboo AH-64 3D RC Mini Apache Helicopter, out of the box, charges, but will not do anything, channel C

Posted by on

5 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Mine worked good for 3 days then died..Top blades wont spin.. It worked really well. The guy at (as seen on TV) shop that sold it to me actually seemed to tell me "Do not buy this!" But I bought it anyway at his word that I cannot bring it back no matter what after 24 hours..spent 90 bucks on this junk and there is NO SOLUTION

Posted on Jan 21, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There is a small set screw on the bottom gear that holds in the upper shaft. You can see these gears through the belly of the helicopter. I had the same problem with the top rotors, and had to go in and re-insert the rotor shaft and tighten the set screw. I applied locktite to the threads to prevent it from backing out. It works now, but one problem I notice is that there must have been a spacer bushing between the two gear wheels. Without the bushing, it will still fly, but I can feel some play in the upper shaft and wonder if over time that the counter spinning gear wheels will start to wear against eachother.

Posted on Feb 10, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Same thing happing with mind low motor go's bad and i cannot find replacment went bad after fling 4 times

Posted on Jan 09, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Bottom blade doesn't spin

Posted on Jan 02, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Same problem with me as well with the Apache from Yiboo..the rotor motor went bad

Posted on Feb 10, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Syma S109g Apache Ah-64 3.5-channels Mini Indoor Helicopter will not charge; the light will keep being red on the USB


Try bringing it to your local electronics store. It might be the connection, or in could be another electrical problem.

Jan 29, 2013 | Syma S109g Apache Ah-64 3.5-channels Mini...

1 Answer

X107 Mini helicopter does not seem to be taking a charge from USB port on computer. ran coptor for about 2 weeks following recharging instructions... rest, recharge of heli in "off"...


Hi, My X107 MINI HELICOPTER does not receive transmit anymore. It was working fine before. It only flys if I hold the remote control right next to the sensor. If I move it away it loses transmit. Both units have full power. How do I solve this problem.

Jan 27, 2011 | Cobra Electronics Cobra RC 3 Channel Mini...

1 Answer

Rc 3 channel apache helicopter how to replace balance bar without the tool kit provided


Cut the balance bar off until the pins are exposed. Use some pliers and squeeze the pin out and then put the new balance bar back on and put the pin back in.

I did it this way without the tool kit, my balance bar was already broken so it wasn't an issue to cut it. It worked for me, I am flying it right now.

Jan 02, 2011 | Apache RC Mini Helicopter AH-64

2 Answers

I crashed my Apache onto a table and when I try to fly it, It keeps spinning out of control. To my knowledge I don't see anything broken. It spins to the right. Please help! thanks!!!


It sounds like your tail rotor is acting up or missing. It keeps your Helicopter from flying in circles.

http://www.start-flying.com/new%20site/heli1.htm

Oct 04, 2010 | Apache RC Mini Helicopter AH-64

1 Answer

Remove and replace balance bar?


Were you able to find a replacement balance bar? I broke mine and can't find one? Thanks!

Apr 18, 2010 | Apache RC Mini Helicopter AH-64

2 Answers

How do you charge the mini ah 64


Turn the remote over and look for the sliding door on the back bottom right (it has a circle and some arrows on it, push in the direction of the arrows) the cable is under this door. Then connect that cable to the helicopter by plugging it into the white slot next to the on/off switch.

Dec 25, 2009 | SYMA Toys industrial SYMA 3 Channel S012...

1 Answer

I have an apache 3 channel helicopter.the top blades no longer spin so the helicopter just spins clockwise very quickly


Same problem I had. There are two motors. One to spin the top blade and a second to spin the bottom. My motor was defective out of the box to spin the top blade. Very poor quality as my AH 64 had a bad circuit board. I had to take parts from one to fix the other.

Sep 04, 2009 | Apache RC Mini Helicopter AH-64

Not finding what you are looking for?
Toys Logo

Related Topics:

4,299 people viewed this question

Ask a Question

Usually answered in minutes!

Top RC Toys Experts

LP

Level 3 Expert

485 Answers

Tom Chichester

Level 3 Expert

33322 Answers

Kevin K.

Level 2 Expert

170 Answers

Are you a RC Toy Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...