Question about Canon PIXMA MP830 All-In-One InkJet Printer

1 Answer

Tiny piece of paper caught in photocopy scroll bar

Hi tiniest piece of paper is stuck in the photocopy section in scroll bar on top of machine. Anyway I can pull this bit out to to get to the paper?Or how can i do a head clean on this part of machine?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers
Re: tiny piece of paper caught in photocopy scroll bar - Canon PIXMA MP830 All-In-One InkJet Printer Printers & Copiers

Try tweezers if can reach it with them.

Posted on Dec 22, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

The pages are printing off center.

A black section down one side of the page could be a couple of things.
1) The Corona Wire Cleaner (The sliding piece on top of the Drum Unit normally either Green or Blue) is not at it's correct rest spot which is where the arrow on the slider and the arrow on the drum unit meet.
2) There is something stuck on the drum or in the laser. Check that there is no scraps of paper caught up in the workings.

Printing too far to one side can be caused by a misalignment of the laser. Turning the machine off for a few minutes may rectify the problem. Otherwise the paper is placed in the tray off-center. Make sure the paper uides on the tray are set snug on the paper.

Hope that helps

Mar 04, 2016 | Brother HL 5140 Laser Printer

1 Answer

Hp laserjet 4345 mfp cannot photocopy anything because the startup button has a red light

Hi Bridgette.

The red light on the startup-button indicates that the machine is not ready for a photocopy. Usally there is something stuck in automated document feeder (ADF). Take a close look and see if can see something in the paperpath. If no luck, try pushing a A4 sheet manually through the ADF and see if something comes out with the sheet. Usally there is a small piece of paper, a paper clip or a staple stuck in the ADF. If nothing found in the ADF, the Scanner Controller Board is probably broke, and needs to be replaced. Good luck.

Dec 31, 2013 | HP LaserJet 4730mfp All-In-One Printer

1 Answer

My canon MP287 cant when photocopy. The paper also started to jam so it cant print. what will I do?

When there is a paper jamb make sure the whole piece of paper is removed because any tiny pieces of paper that are left behind will cause further paper jambs.
If the paper does not feed through the printer correctly then the rubber rollers are dirty/sticky. Clean the rollers with methylated spirits to stop the paper from sticking to the rollers.

Mar 02, 2013 | Printers & Copiers

1 Answer

Jam A,but no paper , 2035

All I can tell you is that there IS paper somewhere in there. It might be the tiniest piece of torn paper that has just managed to get caught in the perfect spot so as to block a jam switch, but there is paper somewhere - I have NEVER found a situation where it wasn't an actual paper jam on one of these machines - but it's way to difficult to give you more advice than that

Nov 28, 2011 | Ricoh Aficio 2035 Copier

1 Answer

Every time I go to copy the paper gets jammed going into C from A. I have pulled out the A drawer and pulled the jam out of C numerous times and it keeps happening. What do I do?

Make sure the machine has toner. Sometimes running out of toner can cause jams. Otherwise make sure there are no tiny scraps of paper lodged anywhere. The tiniest piece can cause a jam. Also, make sure all the sensors are clean (they look like two little eyes). Make sure your paper tray is set to the right size and direction of paper if your copier has that setting - it is a green dial in the paper tray. If you've checked all these things you'll have to call your service tech because it may be a bad sensor or something else.

Mar 04, 2011 | Printers & Copiers

1 Answer

My PC 745 comes up with an error code of a paper jam but I cannot find any jammed paper. Any suggestions.

completely remove the paper cassette and look for A SMALL PIECE OF PAPER stuck inside the machine in the paper path. Also use a flashlight to check for tiny bits of paper in the exit section of the machine where the fuser (hot) rollers are.

Dec 16, 2010 | Canon PC-940 Black and White Copier

1 Answer

Paper is curled inwards when it is ejected from the printer.


Remove the jammed paper. Unplug the printer from the mains and PC. Inspect the rollers, etc for tiny paper piece(s) that may be stuck, or other debris. Try to clean rollers and make sure they are dry. Keep printer unplugged for about 2 minutes and replug and try a test print. Also make sure that you have waited long enough for the printer to heat up before giving a print job. Finally, it could be an issue with the paper sensor. If this is the case, you will probably have to take the printer in for servicing..

Aug 20, 2009 | HP Printers & Copiers

2 Answers

When we put paper in the printer it goes cricked

Lexmark printer have paper roller problem take printer for once service

Jul 25, 2009 | Lexmark X1270 All-In-One InkJet Printer

2 Answers

Nashuatec Photocopier 3722td

Never heard of this model but looks very similar to a Xerox.
3 places to look for
1-open tray and check no paper is behind or on the way up and got stuck.
2-open right side and check bottom lookin ginto the tray, you should see the rubber tires and a black lever sensor, is the sensor ok, is there any pieces of paper on it, is it stuck??
3-look at the fuser section (where it gets hot) can you see any paper there? sometimes they crumble up and get stuck. You willhave to take out the fuser unit and remove the paper.

Aug 23, 2008 | Ricoh Aficio 2015 Copier

1 Answer

Minolta Photocopier EP5000

the non sort bis is the first bin from the top, and by the mean time you can see a hole in the bins for sensing the papers in the bins, the hole from the first bin to the last bin should be un obstructed, as the sensors are on the upper frame and the receptor sensor in the lower frame. so check for any obstruction between theese two sensors through the holes on the output bins

Mar 13, 2008 | Printers & Copiers

Not finding what you are looking for?
Canon PIXMA MP830 All-In-One InkJet Printer Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Printers & Copiers Experts


Level 3 Expert

93802 Answers

old marine
old marine

Level 3 Expert

1294 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Canon Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides