Question about Washing Machines

2 Answers

Hoover error E08

Hello,

Could anyone tell me what the error E08 means on a Hoover Optima OPH 714 D washing machine?

Thanks in advance!

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

Hi I had this fault, google said it was tachometer fault. the e08 fault on my hoover optima was not the tachometer, i checked it, but the fix was very easy, the motor brushes were worn out and i changed them for 10 quid, I made a video of it its on youtube http://www.youtube.com/watch?v=xYn-f78GB4U and it shows you how to test the tacho and how to change the brushes, hope this helps someone

Posted on Sep 18, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hoover oph 714d error code e08

Posted on Aug 04, 2012


6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1768 Answers

SOURCE: Hoover washing machine - door won't open and drum

1. please provide the model number for the washer
2. this is a timer error code and it seems that it locked the door during the spin cycle.
There may be a malfunction sensor or you will need to unplug the washer to reset the washer to complete the cycle.
Something electronic has caused the washer to shut down to protect the electronic circuit. You may have a defective timer.

Posted on Mar 13, 2010

Testimonial: "Thanks for your help, it's working fine now :-) "

FitzOriginal
  • 842 Answers

SOURCE: hoover washing machine Mod OPH 714D Error E16 in

After far more research than I usually have to do, It seems that E16 means "O/C Heater"

Which means that the heating element is open curcuit. Which menas......

Either the heater element has a wire off at the back, or more likely the heater element is burned out.

They are easy to replace. Pull the machine out and remove the rear inspection plate at the bottom of the body (I think this machine has one!, sorry if it doesn't).

At the bottom of the drum, you will see a atainless steel cover, about 4 inches limg and a third of an inch wide, with rounded ends. There will be 2 spade connectors with wires in them (1 either end of the plate) and a 10mm nut in the centre. The nut tightens up a squeeze plate inside that crushes up a rubber seal to hold it in place. Undo the nut fully (you may have to push the little stud bolt that is now exposed in a little to free it off) The element should now withdraw if you grab hold of the spade connectors and tug a little to break the seal before you withdraw it.

Replacement should be the reverse of removal.

Google "Hoover washing machine heating element" to find yourself one on line, or ho to your local Hoover parts stockist

Posted on Jun 30, 2011

Testimonial: "thanks for your help great, having more problems now so it has to go!"

  • 1 Answer

SOURCE: My Hoover Optima OPH 714 D washing machine won't start

Hi, the lights are coming on, but the door lights keep flashing and then nothing happens

Posted on May 09, 2010

Daniel S
  • 4323 Answers

SOURCE: hoover oph 714d optima 7kg

Hi


Error code e005 means the temperature sensor has gone bad. To fix this error you'll need to replace the temperature sensor. It might have happened that the temperature sensor wires have been disconnected from the main board. To replace the temperature sensor you'll need to disassemble the washer and inspect the drum's bottom for the temperature sensor. Also check the wires coming to the sensor fro any cut.

Please post back for any further assistance.


Daniel

Posted on Aug 01, 2010

  • 6277 Answers

SOURCE: I have purchased a hoover

Hi from retired Englishman in SW France,

Manual
You will need to type into your search engine/web browser '(make model number) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct ;-0)

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.

Posted on Aug 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Display has been playing up. A message reading 'EOS' was diplayed just now. The machine has stopped working ?


Canon DLC: Article: Canon EOS Error Messages: An ...

www.learn.usa.canon.com/resources/.../eos_error_msgs.shtml

Canon Inc.Feb 6, 2012 - Canon has installed provision to display Error Codes in EOS SLRs for quite some time. Until fairly recently, the camera could basically display a single, or limited ... today's cameras do provide a wider range of possible read-outs, giving the ....Try removing the USB cable, and firing it normally to see if it now ...

problems installing digital solution disk - Canon Community

community.usa.canon.com/t5/PowerShot/problems-installing.../225
How to Understand Hoover and Candy Washing Machine ...www.espares.co.uk > Advice CentreJul 1, 2014 - Home & Office ... If a fault is detected in your washing machine, an errorcode is likely to flash up. ... how to identify error codes in a Hoover or Candy washing machine. ... code if the machine has a problem and this will either be displayed ...Now what I'm going to do is disconnect the machine and take the ...Error message E03 - Hoover Advice Centre - Hoover Serviceservice.hoover.co.uk > Advice CentreShould the error code E3 appears it is warning that the machine is not draining. You can easily fix this problem by removing any blockages from the drain pump ...Hoover Optima Washing Machine ' OPH ' Fault Codes

Dec 16, 2015 | Candy Domestic EVO14104L White 600 mm...

1 Answer

Hover OPD 714 D 7kg . What does E08 mean


http://service.hoover.co.uk/manuals/OPH714D_1.pdf


user manual

http://www.whitegoodshelp.co.uk/hoover-error-8/

here is a description of the common error your machine has
and how too solve it

hope it helps you...


Mar 04, 2015 | Washing Machines

1 Answer

EOB showing on washing machine


That's E08 (E-zero-eight). Speed sensor on back of motor faulty, or the wiring to it. Can also be a broken magnet in the middle of the sensor coil.

Feb 16, 2015 | Hoover Optima 7 OPH716DF White 600 mm...

2 Answers

Hoover WMH168D error code E08


E08 = Tacho fault

The tacho coil is on the motor and is fitted at the opposite end of the drive belt where the carbon brushes are. This error says something is wrong regarding the tacho coil but it doesn't specify exactly what. Possibilities are varied so unless you know what you are doing, and unless you can see something obvious like the coil has come away from the motor or the motor or drum has seized up it is probably better to call in a professional.

Resistance readings for tacho coils are usually quite high, so if you don't have a sensitive enough meter it could appear to be open circuit when in fact it's reading over 150 Ohms or more and may be ok.


In conjunction with a magnet fitted on the end of the armature shaft each time the motor does a revolution it can be counted by the software or pcb through the tacho coil. This information is used to judge and control the speed of the motor at all times.

If the coil is open circuit the washing machine would lose al control of the motor and in the past the motor would often spin uncontrollable causing damage to the washing machine. These days if an open circuit or missing tacho coil (they can fall off the motor) is detected the machine will stop working and report an error code.

Oct 17, 2012 | Hoover Washing Machines

1 Answer

Hoover optima oph714ds error code e14


hoover optima oph 7d14 working ok but at end of wash cycle error e14 comes up what does this mean

Dec 24, 2010 | Washing Machines

2 Answers

Hoover oph 714d optima 7kg washing machine fault code e05


Hi


Error code e005 means the temperature sensor has gone bad. To fix this error you'll need to replace the temperature sensor. It might have happened that the temperature sensor wires have been disconnected from the main board. To replace the temperature sensor you'll need to disassemble the washer and inspect the drum's bottom for the temperature sensor. Also check the wires coming to the sensor fro any cut.

Please post back for any further assistance.


Daniel

Aug 01, 2010 | Washing Machines

5 Answers

My Hoover Optima OPH 714 D washing machine won't start


Hope your tried switching off the machine for half to one hour, to re plug. Machine might re-set.
If helped, pl click, it could help others.

Dec 07, 2009 | Bosch Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

4,017 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...