Question about U-Line Uline Origins Series Refrigerator/Ice Maker Manual Defrost-COMBO29A

2 Answers

Uline icemaker on boat needs service..

The machine now only makes a few ice cubes before freezing up and cannot cut and drop ice

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 286 Answers

Do you mean frosting up? If so then check the seal around the door. Check to see if the control is set too cold. You may need to make it warmer.it should be between 10 - 15 degrees in the bucket. It could be too cold or it could be too warm.

Posted on Oct 08, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

First do a good cleaning as the manual describe.
check water supply and if still the problem, check power to cutter grid
should be 9 volts all the time

Posted on Oct 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Scotsman cm250ae-1c making very wet ice


It might be a dirty or damaged ice tray. When in the harvest mode the hot gas will be directed through the tray untill the cubes fall tripping the reset to start the freezing cycle again. If the cubes are sticking because of rust or scale buildup the cubes get "overmelted" causing the "wet cubes".CAREFULLY clean the ice tray . Use vinegar or ice machine cleaner do not use any cleaning pads steel wool or sand paper as this will ruin ice tray. Also make sure icemaker is level both ways. Hope this helps.

Dec 27, 2013 | Refrigerators

1 Answer

Uline bi98 ice maker


follow this test. and fix it. use the multimeter.God bless you

If the ice cubes have watery or hollow centers, the icemaker is getting too little water. Alternately, excess water or ice in the bin is caused by too much water. Turn the water supply screw to adjust. If adjustment does not remedy the problem, you may need to service the water inlet valve (see below).
If you suspect trouble with the motor or switcy in an icemaker, use a multimeter to test the component. If the motor or switches test faulty, replace either the bad components or the entire module. If not, you may only need to replace the thermostat (see below)

Oct 28, 2013 | Kitchen Appliances - Others

1 Answer

Sub zero 532, ice maker issue. water enter the cube bin freeze into a block of ice with the cubes embedded. What is the cause of this issue?


There is a few things that you will need to check to isolate the problem. this first thing is locate the fill tube where the water comes into the ice maker. What you are looking for is any ice frozen inside causeing an overspray of sorts. If that checks good, then the next thing is look at the icemaker itself. Look at where the water goes to and freezes. Is it completely full of frozen water? if so then the water valve is sending too much water either because the ice maker called for it or the valve stuck and didn't close when it was supposed to. If its not full, look at the bottom of the ice maker, checking if there are any cracks allowing water to fall into the bin. My personal opinion though would be to change the ice maker and the water valve because of the age of the machine. the bad part is the actual icemaker for that model has been discontinued but I believe you can use a whirlpool style that matches, comes in a kit that has both the water valve and icemaker, and cost almost half the price as the original. that part number is 1129313

May 21, 2012 | Refrigerators

1 Answer

Our icemaker makes cubes, but leaks water from the ice tray area, creating a 2 inch block of ice in the bottom of the ice cube collection bin each night.


Have a look at the manual on page 6 for adjustment procedure.

Also, your leak may be due to a water valve that is not able to turn off 100%. Valve replacement would be necessary. Unplug your icemaker electrical, and empty the ice. Leave the water turned on. If you keep getting water collecting in the bin, you are likely looking at a water valve replacement (not hard at all, just inconvenient).

Oct 12, 2010 | U-Line ULine BI2115B00 Black Echelon 15"...

1 Answer

Free standing uline icemaker in rv still freezes but does not make ice


Hi,

Here is a tip that I wrote about the reasons why ice makers do not work.

Ice Maker Problems and Ice Maker Troubleshooting

heatman101

Aug 24, 2010 | U-Line Icemaker

1 Answer

Ice maker -- not all cubes freezing, running water into rear portion of cube storage tray.


Purchase an inexpensive temperature monitor. Check temp in freezer. Ideally, you should have from 0 degrees to 10 degrees in the freezer. The icemaker calls for water at a certain temperature. There may be an issue with the icemaker, which has a "u-shaped" heater underneath the icemaker to loosen the ice prior to dropping ice in the ice bucket. Or, there could be an issue with your freezer control assembly (typically located in the fresh food compartment). Contact an appliance service company.

Feb 10, 2010 | Amana Refrigerators

1 Answer

Ice Maker won't work


Hello,

If your trying to save a service call you have your work cut out for you. The ice maker is a unit that sits by itself attached to the wall or part of the freezer wall.

There are many reasons why you do not get ice and I will list them.

1- Temp of freezer got too cold and has frozen the pipe that feeds the water to fill the icemaker.
check to see if the icemaker has any ice in the area that fills and makes the cubes.
If the pipe is clogged, very gently put a small tipped screw driver in the fill hose that sites over the ice making row in the ice maker. Be careful you do not push your screwdriver out the back of the refer.
Check to see the freezer temp is not too cold and is freezing that pipe. 0-3 degrees F is good.

2.- check to make sure your water feeding the fridge is on. There is an on off valve to allow the water to feed the icemaker when it needs to fill. This could be bad. there are reset proceedures for the fridge, but unplugging the entire frige for 1 minute and plugging it back in you can listen for the the valve to come on and see if it fills the ice maker resevoir.

3. If it fills and freezes the ice resevoir, then the sensor in the ice tray does not sense the frozen ice and will not cycle and kick cubes. At this point, unless you are super tech, you will need to replace the entire icemaker unit.

Hope this helps.



Mar 21, 2009 | Sub-Zero Bottom Freezer Refrigerator

1 Answer

Uline icemaker must be manually prompted to rotate and drop cubes


If your looking for a icemaker it should be part 402. Call U-line with the serial or model number to be sure they made it.800-779-2547

Feb 24, 2009 | U-Line Icemaker

2 Answers

Ice Cubes won't drop out


The thickness probe should be approximatly 1/4 inch off of the evaporator.Sounds like you might have loose grids on the evaporator.turn the unit off and remove the curtain.use a flash light and inspect the grids.There should not be space in between the joints,if there is the ice will freeze behind the grids and not properly release when in harvest. Also gently pull at the grids,if they pull towards you or wiggle then they are separating. I have removed one of the grids and had the unit continue to run for sometime until the evaporator could be replaced.The plating being spotty causes release issues as well.Finally check the level of the machine,front to back and side to side.Not being level will also cause release problems

Feb 18, 2009 | Freezers

1 Answer

Uline ice maker not cool enough to make/keep ice


one of two things
1. fan under unit stopped up or quit
2. small freon leak usually in freeze plate

Nov 04, 2008 | U-Line Icemaker

Not finding what you are looking for?
Refrigerators Logo

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top U-Line Refrigerators Experts

mike cooper

Level 3 Expert

884 Answers

Dale Copeland
Dale Copeland

Level 2 Expert

102 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Are you an U-Line Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...