I don't have a solution Pamm, but I will add that I've been having the same problem accessing my MMJB. When the program does oepn, it won't allow me to make line in recordings without closing the recorder after each recording and re-opening the line-in recorder window to record another song. Tacky *** Yahoo Music Plus will not provide technical support to the customers they inherited when they took over MMJB! I have a LOT of music converted by MMJB, so this problem really, Really SUCKS!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
It's pretty much just like it says: You either, didn't close out the program right by manually saving the last information you entered. Or,the system shut down while the program was open, like a power failure or accidental reboot. Did you have the task manager open, to close out programs,maybe to regain some memory, accidentally closing the program? Something happen to close out that program before the last entered data was saved
Sounds like an update installed incorrectly or has been corrupted. Using Add remove programs remove the MS Office You have installed. Before you let it reboot tell the computer to run Check Disk on your primary hard drive and reboot the computer. Once the reboot is complete re-install MS Office and see if that solves the problem.
reading your post you mention to "open and close switch"..not sure what refering to...these are the instructions from your vehicles service manual...good luck!
NOTE: All keyless entry remote transmitters (15K601) are programmable and must be set at the same time. NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
Make sure that the anti-theft system is not armed or triggered.
Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Diagnosis and Testing.
Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.
THIS IS MY BEST OFFER. IF YOU HAVE BEEN USING THIS PROGRAM FOR SOMETIME NOW, I FEEL THAT THE PROGRAM HAS PROBABLY DEGRADED AND THIS IS CAUSING THE PROBLEMS. YOUR BEST SOLUTION IS PROBABLY TO TRY TO EITHER REPAIR THE PROGRAM OR DELETE AND RE-INSTALL A CLEAN VERSION WITH THE LATEST UPDATES. SHOWING MORE THAN ONE PROGRAM IN TASK MANAGER USUALLY MEANS THAT YOU HAVE TRIED MORE THAN ONCE TO CLOSE THE PROGRAM. IF YOU THINK YOU HAVE DUPLICATE PROGRAMS, RUN SEARCH>OUTLOOK AND SEE HOW MANY SHOW UP. IF MORE THAN ONE YOU CAN DELETE IT FROM THERE. ALSO, YOU CAN DELETE DUPLICATE FILES ETC. HOPE THIS HAS HELPED.
You don't give much information about what your problem is and unfortunately part of what you did write was truncated.
...If I understand your problem you need to uninstall and reinstall, but can't due to a locked file,
I have two suggestions one FREE program is Unlocker Assistant. (Google it) the other is a nice little FREE utility you can try. Install Microsoft "Windows Installer CleanUp Utility" http://support.microsoft.com/kb/290301/en-us If you find (PROGRAM NAME) listed just hit the delete button. Then do the normal uninstall.
If so then they may have been a change in your program environment. If you do not remember what changes were made or what other programs/changes caused since it last worked -then try reverting to the earlier environment by doing a Restore to a date when you last rembember it worked.
Your options: from time to time go to Running Programs and close what you're done with; or, as you're leaving a progran, check whether it has an Exit or Quit command; or, open iTask, tap and hold on the name of a program, and choose Close this Task from the pop-up menu; or, my favorite, use the on-screen keyboard and tap Control and then Q (upper or lowercase)--that'll work with almost any progran that accepts text input.