Question about Panasonic KX-T7453 Corded Phone

1 Answer



Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Panasonic Master
  • 2,460 Answers

CF to voice mail may be as simple as pressing the FWD/DND button, or reading the manual and dialing the proper 720x code.

It may require some programming via the voice mail system.
Start by dialing 165, the usual VM access code, from your phone and listen to the prompt. If it says you have x messages or enter your password, then the mailbox is active.


Posted on Aug 23, 2008

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

I forgot how to clear the stored voice mails


If you want to delete the actual voice mails, you have to go through your phone company (using their keypad commands) since voice mail is only accessible through your phone (but the voice mail messages are stored through your phone company provider).

Info from the Uniden DECT 6.0 6035 Manual:

Using the Voice Mail Service If you subscribe to a voice mail service, you can use your phone to access your voice mailbox. The new message LED on the handset ?ashes and VM appears in the handset display whenever you have messages waiting in yourvoice mailbox. When you subscribe to the service, your voice mail provider provides you with the access number and the required voice mail signaling tone. You can use your phonebook to store the access number.

Resetting the Voice Message Waiting Indicator

When you receive a new voice mail message, the new message LED on the top of the handset ?ashes and
appears in the handset display. In the event your message alert tone gets out of sync with your phone company's voice messaging system, you can reset back to its original "no messages waiting" state. To reset, press and hold [?nd hs] on the base for ?ve seconds. A beep sounds and the message alert tone is reset.

Here is the manual:
Uniden 6035 1 Owner Manual

Nov 01, 2015 | Uniden DECT 6.0 Cordless Telephone...

1 Answer


The display on a Nortel set will say "message for you" if there's a message in your mailbox. To access your voicemail you can press your open voicemail key if its programmed or press feature 981.If you wish to retrieve your messages remotely, call your office, when the autoattendant answers the call press ** followed by your extension number, your password then # (ex. **2231234#).

Jul 09, 2010 | NorStar M7208 Corded Phone

3 Answers

I left my Vtech phone in New York, left for Europe and forgot to set the answering machine on. When I call in I get a factory recorded announcement that I'm not available, etc. I have my PIN # with me,...

Can you please specify the exact model of the phone? Because the steps in accessing it remotely varies from model to model. Anyway, you can try to follow the steps posted here and then test:

Remote operation allows you to control the functions of the Answering System when you
are away from the Base,and call from an outside telephone line. The Answering
System cannot be accessed from another telephone on the same line. You can access
many of the Answering System functons from a remote location, such as listening to
messages, changing recorded announcements, and recording memos.
Remote operation can only be accessed from a touch tone telephone. If the remote phone
is set to pulse dialing, switch it tone. If tone dialing is not available, you will not be able
to access the Answering System.
Note: All function codes should be entered within 2 seconds in order to activate Remote
To Activate Remote Operation From a Different Telephone Line
1. If the Answering System is OFF, you can dial your telephone number and wait for
the Answering System to answer your call after 10 rings. An announcement, "Please
enter your security code" is given, and you enter your security code to use remote
2. If the Answering System is ON, it will answer your call and begin playing the currently
selected announcement (as with any incoming call).
3. Enter # followed by your 2 digit security code during the announcement. The
default security code is 19.
4. Once the security code is received, a double confirmation beep will be given, and
you are in Remote Operation mode. You can then control the Answering Machine
functions using the telephone keypad.
5. The user can also enter the Remote Operation mode during message recording. The
procedure is the same as step 3. The recording will be stopped after entering the
valid security code "s#xx " and the incomplete message will be deleted. If " 0s"
is entered, the Answering System will release the line, but the recorded message
will still be retained.
6. If the user enters a wrong security code, the system will release the line.
Playing Messages Remotely
1. Press " #1 ", " #2 " or " #3 " on the touch tone keypad to play the messages in the
corresponding mailbox.
2. The system will announce "Mailbox X. You have XX new messages and XX old
messages" and the system will playback the new message only. If there are no new
messages, the system will announce "Mailbox X. You have XX old messages. On
the other hand, in the absence of old messages, the system will announce only the
number of new messages.
Repeat Messages During Playback
1. Press "#4" once during message playback to repeat the current message.
2. Press "#4" twice within 2 seconds to skip to the previous message.
Skip Messages During Playback
1. Press "#6" once to skip forward to the next message.
Stop Message Playback
1. Pressing "#5" during message playback will stop playback.
Deleting Messages
1. Press "#9" once during message playback to delete the current message.
Note: Playback will pause if "#" or " " is entered. Answering System will wait for the
command in the following 2 seconds. If no further tone is entered, playback will be resumed.
Memo Recording
1. Press " 8".
2. After selecting the mailbox by entering command "1", "2", "3", You will hear, "Now
recording", followed by a beep.
3. Enter "#5" to stop recording when you have finished.
Change OGM Remotely
1. Enter " 7" to record a new OGM. You will hear, "Now recording", followed by a
beep to signal start of recording.
2. Press "#5" to stop recording. Your new OGM will playback automatically.
Check OGM1 Remotely
Enter "#7" to review OGM. You will hear playback of OGM followed by a beep.
Turning Answering System ON or OFF
Pressing "#0" toggles the Answering System ON/OFF. "Answer machine on", or "Answer
machine off" will be announced, followed by a beep.
Voice Menu for Remote Operation
The system provides two pre-recorded voice menus to help you during remote operation.
Press " 5", and you will hear the simple voice menu.
The simple voice menu is as follows:
• Press "#1" to play mailbox 1.
• Press "#2" to play mailbox 2.
• Press "#3" to play mailbox 3.
• Press "#5" to stop.
• Press "#4" to repeat the message.
• Press "#6" to skip the message.
• Press "#9" to erase the message.
• Press " 5" for other functions.
(To advance voice menu)
The advanced voice menu is as follows:
• Press "#7" to review outgoing message.
• Press " 7" to record outgoing message.
• Press " 8" to record memo.
• Press "#4" twice to repeat previous message.
• Press "#0" to turn the system on or off.
• Press " 5" to return to the simple voice menu.
Pressing any function code will stop the voice menu, and perform the corresponding
Exiting Remote Operation
1. Enter " 0" on the touch tone keypad to exit remote operation mode. The Answering
System confirms your action with a long beep and then disconnects.
2. The Answering System also automatically disconnects if no key is pressed within 20
seconds during remote operation.

Oct 17, 2009 | Vtech Two Line Digital Answering Machine...

1 Answer

Can't login to voice mail.

You will need to restart your phone system. Unplug black cord. Count to 5 and then plug it back in.
If that doesn't help because password is unknown you will need to login to adminstrative mailbox and reset password on the mailbox.

Mar 05, 2009 | Avaya Lucent Partner 616 Phone

1 Answer

Toshbita DKT-2010 main phone message

Hi Matt,
If your voicemail is a Toshiba in-skin and your main greeting is under 991 mailbox then the last message you change before getting out of programming will be the active message so listen carefully to the prompts and make sure that your new message is the active one when leaving programming. Let me know if this helps. ....Mitelmike

Sep 17, 2008 | Toshiba DKT-2010 Corded Phone

1 Answer

Norstar M7208 telephone

This could be because you have several mailboxes/extensions set up. We've had the same problem in our office.

As a result, from the phone that reads "Messages for you" you can find out which mailbox is attached to the phone.

1. Press "Feature"
The display will read: "Set: ???"

The numbers shown in place of the question mark will be the numbers to the mailbox attached to the phone.

2. Press "Feature"
Enter 981 for voice mail access

The display will read "Login: "
Enter the numbers from the previous action, and if you don't know the password, attempt to use the default passwords of 0000 or 1234.

This worked at our office. I hope it works for you.

If not? We find the site VERY helpful.

If you don't know the password, but have access to the system administrator login, you can reset the password for the set you are trying to retrieve messages.

Good luck

Jul 14, 2008 | NorStar Phones

1 Answer

Listening to voice mail messages

with voice mails there usually is a phone code you have to use if its office phone code i would check with the 1234 or 12345 this is basic for whole office voicemail

Jul 07, 2008 | Panasonic KX-T7633 Corded Phone

1 Answer

Unlocking the security cide to access teh mailbox?

Find out who has administrator access (usually extension 100) and use that phone, call voicemail, press "more" press "MGR" press "CHBX" listen to the voicemail which will prompt/ask you if you want to delete the security code. Say yes!

Nov 06, 2007 | NEC DTU 8D-2 Corded Phone

2 Answers

Norstar Mailbox Problem

The mailboxes don't need to have saved messages, to be full. More then likely what is happening is that when people call in, they are getting a generic/Auto Attendant vm box, and that one is full. Try checking vm box #100, or #10. That is the Nortel standard general delivery vm box. Please let me know is this helps, or if you more help.

May 25, 2007 | NorStar M7310 Corded Phone

Not finding what you are looking for?
Panasonic KX-T7453 Corded Phone Logo

Related Topics:

180 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Phones Experts


Level 3 Expert

94039 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 2 Expert

82 Answers

Are you a Panasonic Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides