Question about Frigidaire FWS1339A Top Load Washer

1 Answer

Frigidaire Washer Model # FWS1399EC

My washer is not putting any water in the tub in the wash cycle. You can put it on any part of the cycle and all you get is spin. The washer only wants to spin with or without water and on any part of the cycle.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers
Re: Frigidaire Washer Model # FWS1399EC

The selector knob has gone bad. The selector will have to be replaced. I've seen a lot of Frigidaires with the same problem.

Posted on Dec 23, 2007

Add Your Answer

0 characters

Uploading: 0%


Complete. Click "Add" to insert your video. Add


3 Points

Related Questions:

1 Answer

My Frigidaire Affinity washer has black mold on the rubber seal .how do I remove it ?

set washer to hot water wash fill detergent cup with bleach put rest in tub run entire cycle i would rewash to make sure all bleach is out

Jul 09, 2014 | Frigidaire Washing Machines

1 Answer

Why does my frigidaire affinity smell

clean it by using 5 cups bleach fill soap cup put rest in tub wash in hot water long cycle run another or 2 after to make sure bleach is gone

Jun 07, 2014 | Frigidaire Affinity ATF7000E Front Load...

1 Answer

Water will not drain. sewer line is not pluged. Customer service says I could have a plugged filter at the pump ( we have dogs). How do I get to the pump to unclog it. Model EIFLS55IIW woody

Hi agnes! Washing machines, including those built by Frigidaire, have internal pumps. These pumps help drain out the water from the washer tub between the wash, rinse, and spin cycles. If the pump is damaged or the pump pulley system is frozen/stiff, the water can become trapped in the washer tub. In both cases, the pump assembly needs to be replaced. You can check by looking for a few signs that a pump is dying or already dead.
1 Start the washer and wait for the washer tub to fill with water. If you do not hear water or hear a motor whirring, the washer motor may be dead.
2 Open the washer lid in mid-cycle. Note whether or not the inner tub is still spinning around. The inner tub is the inside surface of the washing compartment with many holes for water draining. If the tub is not spinning but the motor is running, it is possible the pump is dead. Check the pump pulley by removing the pump from the washer and trying to rotate it by hand. If the pulley doesn't turn freely and is frozen or stiff, replace it. Also, if the agitator is moving but the tub isn't, this is a sign the pump is dying. For front-loading washers, do not attempt to open the door mid-cycle. Look through the glass door. If there is enough water to come up against the door, the pump is malfunctioning.
3 Wait for the washer to finish its cycle. Open the unit. If water is still in the tub, the pump is likely dying or dead.

Sep 04, 2013 | Electrolux EIFLW55I Washer

1 Answer

How do i clean the washer?

you need to put affresh tablets into the tub and set it to clean cycle if it has it or heavy duty with hot water. you can get affresh tablets at just about any store in the laundry detergent isle.

Jun 06, 2011 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Water leaking from the buttom

your washer is off balence its causing your tub from inside your washer to splash out on spin cycle adjust legs get a level then put on top[ washer see if its balanced then try a load.

Jan 26, 2011 | Frigidaire Gallery GLWS1339EC Top Load...

1 Answer

Frigidaire (LTF2940E) Washer starts, stops, starts, stops...

The cycle doesn't advance When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

  • It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.

  • It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

May 07, 2009 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Leaking frigidaire top load washer

yes there a seal under the tub ring make sure tub ring has all the snaps in place

Mar 01, 2008 | Frigidaire GLWS1233A Top Load Washer

1 Answer

Frigidaire Front Loading Washer Leaking

there should be a rubber pipe going to the soap draw to the drum normally there's to pips one at the front of the machine and one on the top it is there have a good look in the machine make sure its un plugged be for putting your hands in the machine ok

Nov 28, 2007 | Frigidaire GLTF1670A Front Load Washer

Not finding what you are looking for?
Frigidaire FWS1339A Top Load Washer Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts


Level 3 Expert

4342 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides