Question about Welding Tools

1 Answer

Where can I get a operating manual for a Craftsman 00920540 Mig Welder

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 437 Answers

Try www.partsdirect.com, this is Sears website. It may have in the parts list a part number for a operation/owner's manual.

Posted on Oct 01, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a craftsman 20511 mig welder it will start welding without pushing trigger


Elmer, If you remove the gun assembly from the machine, if the machine is now not feeding wire, the problem is most likely the gun trigger is faulty. The switch contacts heat up and start sticking over time. If able too disassemble and clean trigger contacts. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
CRAFTSMAN 934 205111 Operator Manual
commin problem with wire feed welder
Wire won stop feeding

May 02, 2016 | Craftsman Welding Tools

1 Answer

Mig welder model# 205680 make a rare noise when turn on


Take the wire out of the hose to the gun and see if noise stops. You may have a short in the Trigger

Nov 16, 2013 | Craftsman 304 FI 95 Amp 120V Flux Core...

1 Answer

Rossi 220BZ Gas/Gasless Inverter Welder MIG MAG ARC Portable Welding Machine


The Rossi 220bz mig welder comes set up to use gas welding, that is with the Mig electrode connected to the positive terminal, inside the machine.
To use gasless mig wleding, the mig wire must be disconnected from the positive terminal inside the machine and reconnected to the Negative terminal - inside the machine. Open both the side coveres of the welder using a phillips screwdriver. Use a 13mm spanner to undo the hex nut holding the thick copper Mig lead to the terminal named positive, then lead it through the machine to the terminal on the oppisite side of the machine, labelled negative and screw it in place there with a 13mm hex screw. Be carefull not to bump any of the many electric parts inside the machine.
If you run the Mig welder in gasless mode with positive earth and positive elecrode it will blow the household electric fuse.
If you run the Mig welder in gasless mode with negative earth and positive electrode it will work, but the end of the Mig gun tip will get very very hot and start smoking abnormally from excessive heat.
But if you take the side covers off and rewire it (takes about 10 minutes) to negative Mig Electrode, the Mig gun tip remains cool and does not overheat. You will have to cut just one white cable tie, to get an extra inch or so of free Mig cable, so the thick copper Mig lead will reach accross to the terminal on the other side of the machine named negative. Stick the earth lead at the front in the positive terminal.
I did this on my Rossi 220bz mig welder.
http://www.weldequip.com/gasless-mig-wire.htm

Jun 25, 2013 | Welding Tools

1 Answer

Need an operating manual for the century 80


Do a web search for lincolnelectric.com and look for the manual for this model.

Oct 12, 2009 | Lincoln Electric LE 83180 Century...

2 Answers

Clarke MIG welder parts??


what model is your clarke? i have a 125en which is the exact same welder as a craftsman, you could probably get a new feed motor or other parts for the welder itself from sears, the gun is a tweco style gun same as lincolns, so if you need tips or anything you can get those just about anywhere welder stuff is sold. i hope i helped.

Apr 09, 2009 | Clarke Power Products Welding Tools

1 Answer

Craftsman welder


.04 tips with .04wire with .04 liner etc.........
.025 tips wire .025 wire with .024 liner etc.....

Jan 17, 2009 | Welding Tools

Not finding what you are looking for?
Welding Tools Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Welding Tools Experts

Brad Brown

Level 3 Expert

16166 Answers

Bill Boyd

Level 3 Expert

45402 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Are you a Welding Tool Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...