Question about Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher

1 Answer

Check water light comes on when started,water feed filter has been replaced

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi Guys

The water outlet hose was blocked.

Thanks

Jim

Posted on Oct 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water pump runs constantly but no water pressure or water comes out of hose.


Lots of possibilities. Inlet filter might be clogged. I once had a lizard crawl into a water feed line, totally blocked the feed. Check valves might be stuck closed. Discharge hose might be plugged. Pump might be trashed ( if it is a vertical engine it is probably a throw away pump) Nozzle might be plugged.
Disconnect the hose at the discharge and turn on the water supply. It should have a stream of water even without the motor running. That will check the inlet filter, feed pipe and check valves.

Oct 07, 2014 | Garden

Tip

PRIMO BOTTOM LOAD WATER DISPENSER, BLINKING LIGHT


We started getting a blinking light... indicating the jug needed replacement... after installing a full jug. The unit would cycle, then the red blinking light would come back on. Upon careful inspection of the feed tube and lines, it was realized that the plastic line on the intake of the pump body had been inadvertently pulled out just slightly (presumably from jostling the jug around during replacement). I believe that this breaks the seal the unit requires for suction, and caused the fault. I simply pushed the (white) plastic line back into pump body and heard an audible 'click'. Unit works fine now. I hope this helps, as these units are not exactly cheap.

on Oct 30, 2013 | Primo Grills And Smokers Primo Bottom Load...

1 Answer

Whirlpool LHW0050PQ4 Solenoid Failure? Problem started yesterday after 4 years of dependable usage. After a load was completed and the "Done" light on, I opened the (unlocked) door and...


the water control is by a diaphragm that is controlled by a solenoid
when the solenoid is activated , a small needle unblocks a hole and the diaphragm opens to allow flow
when the water is shut off the needle blocks the hole and the incoming water closes the diaphragm off so stopping flow.
sand will affect that operation so new valves ($20.00 approx ) will fix that problem or maybe just pulling the diaphragm section off and cleaning it out
next the filters in the inlet hoses are under the rubber washers so pull the washer out and the filter will come out
next if you have a mains supply problem, the answer is to fit a big blue filter ( 4" X 20" ) paper element filter to the house supply line
that will filter out any dirt and rubbish down to 10 microns and if you go a carbon filter down to around 3 microns ( around hair thickness size)plus and taste
as for the water in the tub problem , you may have to get a technician in as that would be the program not shutting of the inlet water while spinning or a pump not operating correctly ---blocked inlet or inlet filter

Feb 28, 2017 | Whirlpool LHW0050PQ Front Load Washer

1 Answer

My system vibrates & resonates loudly when the ordinary tap is switched on. Also, water comes out of the filter tap when it isn't turned on, sometimes in a stream, other times constantly dripping. Have...


You are getting water feeding back to the kitchen faucet from the filter system. A check valve needs to be installed on the line feeding the drinking water system to prevent this. Excess pressure may also be causing these problems. An in-line flow restrictor may alleviate the dripping.
RJ

Oct 27, 2010 | Culligan Under Sink Water Filter

1 Answer

GE Profile side by side. Water flow at door dispenser is slooooow. Replaced filter - no joy, replaced solenoid, still slow. Now I have narrowed the problem down to the feed/return lines to/from & the...


Your water line could be frozen in the door. You can disconnect the line at the bottom before it goes into the door at the bottom hinge. Push the dispenser button and see if it comes out there. If it does, leave the door open till it thaws.

Sep 25, 2010 | GE Refrigerators

1 Answer

A replaced the Culligan 250A filters and now everytime you turn on the water from any faucet in the house you here 2 beeps.


I suggest installing an in-line check valve on the feed line to the Culligan filter and resetting the meter on the filter system. You may be getting water water feeding back out of the filter system when other faucets are run causing the meter alarm.
RJ

Aug 20, 2010 | Culligan Under Sink Water Filter

1 Answer

Where is the fuel filter on a 1978 mercury 500 50 h.p. out board motor located. im asking cause my boat works awesome until i get close to top speed it starts bogging out in 1 sec intervals and i dont know...


standard system is in the fuel pump on side of engine where the feed pipe comes in , very basic and i would fit a water seperating filter in the boat which is the size of an oil filter and saves stripping the carbs when you get dirt and water in your fuel ! check the diaphram is ok and not hard and no leaks !

Jun 07, 2010 | Light Outboard Motor Boat Bass Fishing...

1 Answer

Not draining


Check the inlet hose to the pump from the drum, make sure it is not blocked, remove outlet hose and run water through it.
If these are clear and the filter is clear, you need to establish that the pump itself is o/k.
Select drain and see if you can hear the pump running, if you can't, then you need to check that is getting a mains feed to it.
If feed is there, then the pump is faulty. Replace
If no feed ,then you need to look further.
Plz rate my solution.
Thanks.

Dec 30, 2008 | Hotpoint Aquarius WMA56 Front Load Washer

1 Answer

Hotpoint dishwasher model BFI62


water leaking into base of machine. tip dishwasher back and drain out water. then check all seals intact, i.e. around arms, around salt holder etc

Dec 23, 2008 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

I have a wf321p hotpoint aquarius washing machine. it never stops draining.


The issue you have is actually one i have come across on several occasions, these models have a couple of weaknesses in the electronics, it the door latch fails then it can feed voltage back into the electronics and cause all sorts of odd issues, unfortunately it's a matter of replacing the electronic controller and then see what else if faulty, in most cases it's cheaper to replace the machine.

May 14, 2017 | Washing Machines

Not finding what you are looking for?
Bosch 24 in. SGS43C12 Classixx Free-Standing Dishwasher Logo

511 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...