Question about Proform 730 Folding Treadmill Model PFTL71104 - !

1 Answer

I need a Motor Speed Controller Model MC-60 - Proform 730 Folding Treadmill Model PFTL71104 - !

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,230 Answers

Hi there,

Well I find a controller on ebay.com
You can purchase it from below link -

http://cgi.ebay.com/Repair-Rebuild-MC-60-Treadmill-Motor-Controller-MC60_W0QQitemZ140347773158QQcmdZViewItemQQptZExercise_Fitness_Cardio?hash=item20ad6110e6


Just copy and past the above link to your web browser and follow the site instructions to purchase it....

Good Luck!!

THanks

Posted on Oct 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I wire a Kenwood MC-60 mic to a Galaxy 2517


You can. You'll need to figure out the function of the MC 60 wiring and also that of the stock 2517 mic to rewire the MC 60 to it.
jeverge2@gmail.com if you need help with that, I'll see what I can find for you

Aug 24, 2014 | Radio Communications

1 Answer

MC 2100 LS-30 DIAGRAM SCHEMATIC


mi tarejeta MC 2100 LS-30 REV. Tiene la resistencia r21 carbonizada mu pueden desir el valor.

May 14, 2013 | FreeMotion Xtr 90 Motor Speed Controller...

1 Answer

My proform 750 CS will power up and incline but the motor won't start moving. While performing troubleshooting on the MC-60 SCR Motor Controller the D11 LED is the only LED lit up on that circuit


please LUBE the deck belt+rollers bearing. see the video attached.
If the problem persist TIME to replace the old deck belt board.
This happen because the lack of maintenance schedule in LUBE.
God bless you

note:forget it the LEDS troubleshooting, you must see the functions ONLY when there are electronic problem with the electronic board+sensor2_4_2013_6_01_12_pm.gif

Feb 04, 2013 | Exercise & Fitness

1 Answer

I need a motor speed controller model MC-60


Go to the next company and you need to buy:

www.fitnessrepairparts.com

sincerely. God bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Oct 26, 2011 | Exercise & Fitness

1 Answer

I need a speed controller model MC-60


GO THE NEXT COMPANY WEB PAGE:

www.fitnessrepairparts.com

you need TO BUY.

sincerely. God Bless you.

E.CUADRA
MANAGUA, NICARAGUA. C.A.

Oct 26, 2011 | Exercise & Fitness

2 Answers

I hav e Model # HRTL7183 The speed control buttons do not work so it will not run I am told the contol board is no longer available


the control board is still available for this i am sure of it. you may have to get a used one. look at ebay. this is an icon treadmill i am sure. probably has a mc-60 or somethin like that. i have a few spares. look on the treadmill and it should say on the control board what type of board it is. it is located in the motor area the computer board should say what model it is. go to treadmill doctor. com

Jan 27, 2011 | HEALTHRIDER R65 Treadmill

1 Answer

Nordic Track c2200 no speed signal. My NT c2200 treadmill behaved erratically briefly (sudden speed changes up and down) before quitting altogether. The console now behaves as though it's working but the...


It likely is the controller if it was speeding up and down erratically. Check the position of the reed switch to make sure it is positioned about 1/8" away from the magnet in the side of the front roller pulley. Run a diagnostic program as follows. Press the stop and speed arrow up buttons until you insert the key. Press the stop once or twice until you get to a screen with 2 sets of zeros. Now press and hold the speed arrow up button until one number set shows 8.5. The unit will go to full speed so be careful not to be on the walking belt. The other number set should top out shortly at either 10.0 or 12.0 based on whether your speed buttons go up to 10 or 12. If the motor races past your top number,( don't let it run that way as you may damage the motor), pull the key. If the readout is above or below your target by more than .4 and not flucuating a lot, you may need to tune the potentiometer on the controller. Counter clockwise turn with a phillips screwdriver turns the motor speed down. Be carefull not to short out the controller board by touching components with screwdriver. If not comfortable ask a friend with electronics background. If you turn the pot. too far it will break. It will not go a full revolution in either direction and tiny movements are recommended. Again I believe your controller needs replacing.

Oct 01, 2010 | Nordic Track Exercise & Fitness

2 Answers

I need a replacement motor, 60 HZ 2.7 amp, for a Lakewood fan Model HV-217SPC


GRAINGER.COM ... .GOOD LUCK AND I'FN I WAS ANY HELP PRAISE IS APPRECIATED .. SO VOTE JAY MOTORWIZJ

May 28, 2010 | Lakewood MC-42 Fan

1 Answer

I have an existing ceiling fan with a three speed controller. The low speed setting was too high so I have engaged an electrician to install a variable speed controller, Clipsal 32E500F Series. The new...


some manufacturer already attached a variable speed controller when you purchased them, meaning the unit requires this control, but in your case when you purchased it, it does not have any, meaning they sell it to the market as ready to use, so why install additional control?

There might be an installation error during the assembly, so all you have to do is just interchange the wire connected to the control from LOW, MEDIUM and HIGH, it is a trial and error thing but it won't affect or damage your unit, maybe your high speed connection was connected to a low speed control, so just inter-change it. Remove the variable speed control

Nov 01, 2009 | Aloha Housewares (93645) Ceiling Fan

Not finding what you are looking for?
Proform 730 Folding Treadmill Model PFTL71104 - ! Logo

Related Topics:

1,105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proform Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...